Asko TL751 XXLT Скачать руководство пользователя страница 42

Страница: 42 / 61

Belt Switch (

Micros

witch)

1. Function

• The switch cuts the power supply to the motor when a belt is broken.
• The switch is on when the belt has adequate tension but off when

the belt gets loosened or broken, blocking the power supply to the
motor.

2.. Specification

• Microswitch with two terminals, NC (normally closed) type

free state : COM and NO are c

losed

pushed down : COM and NC are disconnected

• Electric rating : 250V 16A 1/2HP
• Type name : GSM-V1622A2

3. Checking method of malfunction

• The switch is in normal operation if the drum rotates.
• Start the unit and check if the drum operates.
• If the drum fails to rotate, press the power button to stop the dryer and then again to check if the motor

runs.

• If you can not hear the running of the motor, disassemble the dryer and check the belt switch contact.
• Press the

arm

of the belt switch. If the resistance between contacts is greater than 1, replace the belt.

4. Procedure of replacement

Remove Top

Plate

Remove Front Panel

Ass

embly

Remove Front

Cabinet

Assembly

Remove Upper

Frame

Remove

Drum Ass

embly

Check the position of the part.

Normal belt - switch lid free

Damaged belt - switch lid pressed by the spring

Part Code : 3619047500

Содержание TL751 XXLT






























































Результаты поиска

Содержание TL751 XXLT

Отзывы:

Похожие инструкции для TL751 XXLT

Бренды по названию

Популярные бренды

Asko TL751 XXLT, Руководство по обслуживанию

Результаты поиска

Содержание TL751 XXLT

Отзывы:

Похожие инструкции для TL751 XXLT

Бренды по названию

Популярные бренды