Asist AE3B60DN, Инструкция по эксплуатации

Страница: 42 / 71

ADDITIONAL SAFETYINSTRUCTIONS
Before use
Note: Remove all packaging materials from the
product.
Hold the device by the insulated handle surfaces as
the sanding belt could strike the device’s own mains
lead.
Damaging a live wire could result in the metal parts
of the device also becoming live and could lead to an
electric shock.
Danger of fire from flying sparks !
Sanding metal creates flying sparks. For this reason,
always make sure that nobody is placed in any danger
and that there are no inflammable materials near the
working area.
When undertaking prolonged sanding of wood, and
in particular when working on materials that give rise
to dusts that are hazardous tohealth, the sander must
be connected to a suitable external dust extraction
device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
The belt sander is designed for the dry sanding of
large surfaces of wood, plastic, metal and plaster and
painted surfaces. The device is to be used for dry
sanding only.
Do not sand materials containing asbestos.
Asbestos is a known carcinogen.
POISONOUS DUSTS!
Sanding paints containing lead, some types of wood
and metal for example may give rise to hazardous or
poisonous dusts and represents a risk to the health of
the person operating the device and to anyone near
the work area.
Wear safety glasses and a dust protection mask!
Securely support the workpiece. Use clamps or a vice
to grip the workpiece firmly. This is much safer than
holding it with your hand.
Never support yourself by placing your hands near or
in front of the device or the workpiece surface. A slip
can result in injury. If a dangerous situation arises, pull
the mains plug immediately out of the mains socket.
Always work with the mains lead leading away from
the rear of the device.
Avoid contact with the moving sanding belt.
Do not work on moistened materials or damp surfaces.
Always switch on the device before placing it against
the workpiece. After sanding, lift the device from the
workpiece before switching it off.
When working always hold the device securely with
both hands (see Fig. D). Always keep proper footing
and balance.
Switch the device off and allow it to come to a complete
standstill before you put it down.
When taking a break from your work, before carrying
out any tasks on the device itself (e.g.
changing the sanding belt) and when you are not using
the device, always pull the mains plug out of the mains
socket.
- Use protective equipment against
noise, dust and vibrations!!! KEEP
THESE SAFETY INSTRUCTIONS FOR
FUTURE REFERENCE!!!
DESCRIPTION (A)
The belt sander is designed for dry sanding of large
surfaces of wood, plastic, metal, plaster and painted
surfaces. The device may only be used for dry sanding.
Always use a sanding belt and grade of grit suitable for
the particular surface you are sanding.
The speed selected should also be appropriate for
the material. The device is not intended for commercial
use. Any other use or modification to the device shall
be considered as improper use and could give
rise to considerable dangers. The manufacturer will
not accept liability for loss or damage arising from
improper use.
1 Belt speed adjuster wheel
2 Locking knob
3 ON / OFF switch
4 Toothed belt cover
5 Dust extraction spout
6 Belt adjuster screw
7 Auxiliary handle
8 Ventilation slots
9 Tensioning lever
10 Dust collection box
Accessories:
1 x cartridge with dust filter
1 x suction connection
2 x clamp
1 x sanding belt
PICTOGRAMS
Pictograms stated on the product packaging:
a) Power values
b) Power consumption
c) No-load speed
d) Grinding belt
a b c d e
USE AND OPERATION
The ASIST power tool is designed for domestic or hob -
by use only.
The manufacturer and the importer do not recommend
to use this equipment under extreme conditions and at
high loads. Any other additional requirements must be
agreed upon by the manufacturer and the buyer.
Preparing for use
Tensioning / changing the sanding belt
Risk of injury! Before you carry out any work on the belt
sander always pull the plug out of the mains socket.
1. Then release the tensioner for the sanding belt
42