31
Troubleshooting Guide
Instruction Manual
AP01 : WJ32
For watch functions in general
For running measurement functions
Problem
Cause
Remedy
Refer to
The display has be-
come blank.
The battery has run down.
Request the retailer from whom
the watch was purchased to re-
place the battery with a new
one immediately.
－－
The watch gains or los-
es time temporarily.
The watch was left in a cold or hot
place.
The accuracy will be recovered
when the watch returns to the
normal temperature. Set the cor-
rect time before use.
P.9
The blur on the glass per-
sists.
Water got inside the watch due to dete-
rioration of the gasket or other reasons.
Consult the retailer from whom
the watch was purchased.
－－
The timer does not re-
peat countdown.
The number of repetitions is set to
“
1
”
in the TIMER SETTING mode.
Set the number of repetitions
as desired in the TIMER SET-
TING mode.
P.11
The alarm will not ring
at the designated time.
The time zone set for the TIME mode
differs from that set in the ALARM SET-
TING mode.
Activate the ALARM SETTING
mode to check if the time zone
is set correctly.
P.12
The alarm is not engaged for the alarm
channel for which the alarm time is set.
Select that alarm channel in the
ALARM mode, and activate the
ALARM SETTING mode to en-
gage the alarm.
P.12
The battery may near its end.
Check the battery life indicator.
If it indicates that the battery
nears its end, request the retailer
from whom the watch was pur-
chased to replace the battery
with a new one immediately.
P.8
The warning and time-
u p b e e p s w i l l n o t
sound.
The battery may near its end.
Check the battery life indicator.
If it indicates that the battery
nears its end, request the retailer
from whom the watch was pur-
chased to replace the battery
with a new one immediately.
P.8
The backlight will not
light up.
Problem
Cause
Remedy
Refer to
“
- - - spm
”
is shown for
the SPM value for a
short time after the run-
ning is started.
It takes approximately 10 seconds af-
ter the running is started for the built-
in sensor to recognize that the move-
ment it senses is that of running.
The watch is intact, and can be
used as usual. If the SPM value
will not be shown after 10 sec-
onds, the watch may be out of or-
der. In that case, consult a nearby
ASICS service facility.
－－
Though lap time mea-
surement was made,
neither SPM nor pace
is displayed.
This watch is so designed that, if the
lap time measured is less than 30
seconds, the average SPM or pace of
the lap is not displayed, as a signifi-
cant measurement error may be in-
volved.
Measure a lap time when more
than 30 seconds have elapsed
from the start.
－－
The algorithm was cus-
tomized, but the dis-
tance run indicated on
the display differs from
that actually run.
The data measured when you ran at a
speed too faster or slower than usual
was input in the SET_UP mode.
Use the data measured when you
run at a usual speed to customize
the algorithm in the SET_UP
mode.
P.19
The AVG_PACE data
cannot be set.
Data beyond the settable range of the
running data was input. For example,
invalid distance was set, or inappro-
priate adjustment of the transferred
time was made.
Set the running data within the
ranges below:
SPM: 60 ~250 SPM
Pace: 1
’
00
”
~ 19
’
59
”
/km or 1
’
37 ~ 32
’
10
”
/mile
P.21
The SLOW PACE and
FAST PACE data can-
not be input.
An SPM value which is the same as
the AVG_PACE data cannot be input
as the SLOW PACE or FAST PACE
data.
Input an SPM value different from
the AVG_PACE data.
P.19
The SLOW PACE and
FAST PACE data was
lost.
If the AVG_PACE data is updated, the
SLOW PACE and FAST PACE data
will be reset to
“
0
”
.
Input the SLOW PACE and FAST
PACE data again.
P.19
When used for walking,
the SPM indicated on
the display differs from
that actually counted.
This watch is intended to measure
the number of steps during running,
and the accuracy of the SPM mea-
surement during walking may vary
significantly from user to user.
Swing the arms as sufficiently as
possible while walking.
－－
