ASEM CPU 1021/A Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 69

background image

CPU 1021/A

User’s Guide

52

Asem S.p.A.

IGD

– LCD Control Sub-Menu

IGD

– LCD Control Sub-Menu

IGD - Panel Scaling: Controls calibration of the scaling of the LCD panel
[Auto].
IGD

– Portrait Mode: [Auto].

Spread Spectrum Clock Chip: Controls the Spread Spectrum Clock for
the video
Default: Off

DVMT 4.0 Mode

Select the configuration “Dynamic Video Memory Technology”. It defines
the amount of memory which will be assigned for the integrated video.
Fixed: Fixed graphic memory will be assigned.
DVTM (default): Only the pre-assigned memory will be assigned during
start-up. Further memory is assigned if necessary during start-up.
Combo: Combines the functions Fixed and DVMT.

Pre-Allocated Memory Size [8MB]

Determines the sum of the pre-assigned memory for the integrated video
[1MB] [8MB]

Total Graphics Memory [128MB]

Selects all memory (pre-assigned, Fixed, DVMT) assigned for the
integrated video.
[32MB] [64MB] [128MB]

«
...
58
59
60
61
62
...
»

Содержание CPU 1021/A






































































Отзывы:

Нет отзывов

Похожие инструкции для CPU 1021/A

Бренд: Ublox Страницы: 23

Бренд: IBASE Technology Страницы: 58

Бренд: austriamicrosystems Страницы: 8

Бренд: Gigabyte Страницы: 96

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

Бренд: MAX power Страницы: 20

Бренд: IBASE Technology Страницы: 76

Бренд: EPOX Страницы: 84

Бренд: JETWAY Страницы: 48

Бренд: Honda Страницы: 692

Бренд: OLIMEX Страницы: 26

Бренд: Intel Страницы: 36

TPS5420EVM-175 SWIFT

Бренд: Texas Instruments Страницы: 16

GA-N650SLI-DS4L

Бренд: Gigabyte Страницы: 100

Бренд: DFI Страницы: 107

Бренд: Rosch Computer Страницы: 43

Бренд: Gigabyte Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды