ASEM CPU 1021/A Скачать руководство пользователя страница 51

Страница: 51 / 69

BIOS Setup

Asem S.p.A.

How to use the Setup

The

Setup

is divided into various menus. To navigate and make

settings, you will need to use the following keys:

(moves the cursor among various menu items)

ENTER

(allows access to the selected menu)

/ -

PgUp

PgDn

(increase/decrease value within selected menu)

Main

BIOS version

Show the currently installed version of BIOS.

CPU Type

Shows the type of processor installed.

CPU Speed

Shows the speed of the installed processor.

System memory

Shows the value of the conventional memory detected during system boot up.

Extended Memory

Extended memory (over first MB) detected during diagnostic functions at
start up, fully available to the operating system.

System Time

To select the time, use the keys + and - . Then confirm with ENTER.

System Date

To select the date, use the keys + and - . Then confirm with ENTER.

Legacy Diskette A

Use the keys + - to select the type of floppy drive. The possible choices
include: 360 KB, 1.2 MB, 720 KB, 1.44 MB, 2.88 MB, None.

Содержание CPU 1021/A






































































Результаты поиска

Содержание CPU 1021/A

Отзывы:

Похожие инструкции для CPU 1021/A

Бренды по названию

Популярные бренды

ASEM CPU 1021/A, Руководство пользователя

Результаты поиска

Содержание CPU 1021/A

Отзывы:

Похожие инструкции для CPU 1021/A

Бренды по названию

Популярные бренды