manualshive.com logo in svg

ASD FieldSpec 3, Руководство пользователя

Поделиться
Скачать
ASD FieldSpec 3 Скачать руководство пользователя страница 81

ASD Document 600540 Rev. J

71   

FieldSpec® 3 User Manual

 www.asdi.com

Chapter 7  Field Measurements

Step 2

Place the glass into the sink.

Step 3

Place 220 grade wet sandpaper onto the glass.

Step 4

Gently move the Spectralon reference in a figure 8 motion on the sandpaper, 
using water as needed to wash away the thin layer that is sanded off. 

Step 5

Blow dry with clean air or nitrogen or allow the material to air dry. 

Step 6

If the material requires high resistance to deep UV radiation, the piece should 
be prepared as above, then either of the following two treatments performed.

1

Flush the Spectralon piece with >18 milli-ohm distilled, deionized water 
for 24 hours.

2

Vacuum bake the Spectralon piece at 75° C for a 12 hour period at a 
vacuum of 1 Torr or less. Then purge the vacuum oven with clean dry air 
or nitrogen.

WARNING!

Do not use oils or soaps to clean the Spectralon white 
reference.

7.11.3

White Reference Procedures

White references should be collected approximately every 15 minutes and can 
be varied depending on whether conditions are changing rapidly or not 
changing very much. The Spectralon puck should be used when optimizing 
and taking a white reference measurement. 

Note:

For best results, the Spectralon puck should be at the same distance and angle 
from the foreoptic as the sample will be during measurements.

When saving reflectance data, point the probe at the Spectralon with the same 
viewing geometry for a minute or two every few measurements. If the relative 
reflectance of the Spectralon is less than or greater than one, a new white 
reference may be needed. If the relative reflectance of the Spectralon is 
greater than one, re-optimization is recommended.

The FieldSpec spectroradiometer should be re-optimized for:

•

Light changes.

•

Any atmospheric changes.

•

Temperature changes.

•

Whenever accessory probes are changed.

Note:

Environmental conditions can change rapidly or slowly. It all depends on 
clouds, wind (affecting temperature), instrument warm up time, etc.

 

Содержание FieldSpec 3















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды