Asco 460 Скачать руководство пользователя

Страница: 21 / 24

For troubleshooting, call technical assistance at 1-800-237-4567 or [email protected]

IO-70064

05/2020

LED Status Indicators

The SPD diagnostic display panel shows the status of each phase of the

SPD with diagnostically controlled green/red LEDs). If a unit is operating

correctly, all of the phase LEDs will be illuminated green. To test the integrity

of the diagnostics for each phase, push the button below the phase LEDs on

the diagnostic display panel. The green LED will turn red and the alarm will

sound, if the alarm is enabled. Releasing the test button will complete the

test; the red LED will turn green and the alarm will shut off.

If an inoperable condition occurs on any phase, the audible alarm sounds

and the corresponding phase LED on the diagnostic display panel is

extinguished and the service light will illuminate. This indicates that the

device needs service by qualified electrical personnel.

The audible alarm can be silenced, until a qualified person is able to

evaluate and service the SPD, by pressing the alarm silence button. The

alarm will silence and the LED above the button will be lit. The red service

LED will continue to be illuminated until the inoperative condition has been

cleared.

Figure 10:

Diagnostic Display Panel

Phase A, B & C:

Green LED indicators—one per phase. Green is good.

Out indicates problem. Every suppression element in this SPD is monitored.

(N-G indicates on Phase A)

Service LED (Red):

LED illuminates in the event of problems. This indicator

is logic-connected to the Phase LEDs. Should a Phase LED go out, the

Service LED will illuminate and the Audible Alarm will sound.

Test:

Tests red Service LED and Audible Alarm, and changes state of Dry

Contacts.

Alarm Silence:

Turns Audible Alarm off. (Alarm is deactivated when the

Silence LED is illuminated.)

Surge Counter Count:

(if equipped) Increments optional surge counter by

one. (+1)

Surge Counter Reset:

(if equipped) Resets optional surge counter to zero.

(0)

Silence

9294_R1

Test

Count

Reset

Surge Counter

Service

Full Protection

When One (1)

LED Per Phase

Is Illuminated.

400 SERIES

Surge Protective Device

ASCO 460/465/480/485 Surge Protective Device (SPD)

Operation

Содержание 460

























Результаты поиска

Содержание 460

Отзывы:

Похожие инструкции для 460

Бренды по названию

Популярные бренды

Asco 460, Руководство по установке и эксплуатации

Результаты поиска

Содержание 460

Отзывы:

Похожие инструкции для 460

Бренды по названию

Популярные бренды