ASCO POWER TECHNOLOGIES C2ADTL Скачать руководство пользователя

Страница: 21 / 25

Chapter 3 Maintenance and Troubleshooting 17

ASCO Series 230 C2ADTL Transfer Switch User Manual

Chapter 3 Maintenance and Troubleshooting

This chapter describes the transfer switch installation, commissioning and common faults and maintenance methods.

3.1 Start Up / Function Test

1. To Test Manual Operation

Two power supply Sources must be disconnected before manual testing can begin. Refer to chapter 2.2.1 to run

Manual Operation mode. Operate the transfer switch from I position to II position and turn back to I position with

handle. The operation should be smooth, without interruption. If so, switch is operating correctly in manual mode.

2. To Verify Voltage Detection

First make sure the rated voltage of the transfer switch on the nameplate is the same as the dual-power supply

rated voltages. Next, review the C2000 or the C1000 controller, to make sure the power is being supplied to

transfer switch. Source I and Source II Auxiliary Indication LED lights are on (green), This should indicate your

wiring is correct.

If using the C2000 controller, Double-check and measure the dual-supply voltage, to make sure voltages are

consistent to what is indicated on the C2000 controller .

DANGER

！

When measuring Voltage, pay attention to not touch the terminals and copper bars, otherwise it could result in death, or serious

injury.

3. To Test Electric Operation

This is used to test the controller in electric operation mode and operate the transfer switch electrically.

Using C2000 controller:

Menu Setting

2. Settings

Control

2.4 Control Mode

Manual Control

2.4 Control Mode

S1 Prior

Enter

Down

Enter

Down

Enter

Down

Operation

Description

Settings

Scrolling the main menu to
“Setting” ,and press “Enter”
button.

Control Mode

Scrolling the Setting menu to
“Control Mode” ,and press
“Enter” button.

The Control Mode Menu will display

the last settings.for example,the

default control mode is S1 Prior.

Control Mode

Scrolling the Control Mode menu
to “Manual Control” ,and press
“Enter” button.and then setting is
ok,system will be reset.

Must press the “Enter” button when
the Control Mode is setted,the

contorller will be reset to complete

the set.

Содержание C2ADTL


























Результаты поиска

Содержание C2ADTL

Отзывы:

Похожие инструкции для C2ADTL

Бренды по названию

Популярные бренды

ASCO POWER TECHNOLOGIES C2ADTL, Руководство пользователя

Результаты поиска

Содержание C2ADTL

Отзывы:

Похожие инструкции для C2ADTL

Бренды по названию

Популярные бренды