ASCEL Electronic AE20218 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 48

background image

USB Driver Installation

The driver for the virtual serial port must be installed before
the software can be used. Drivers for all supported operating
systems are included with the device., They can be found in the
"Driver" directory on the CD.

Note: Newer Windows OS (starting with Windows 7) can install the driver automatically if an
Internet connection is present.

Note:  You   can   change  the  number  of  the  COM   Port  assigned   by   Windows  after  the  first
connection is made, by going to Control Panel / Device Manager and selecting the port. Select
Properties / Port Settings / Advanced and assign a new number. It will remain even after the
device is disconnected and connected again later.

Software Installation

The   PC   software   can   be   found   in   the   "Software"   directory.
Execute   setup.exe   to   install   the   software.   There   is   also   a
portable   version   of   the   software   in   the   "Portable   Software"
directory that does not require installation.

Note: The .NET-Framework (at least version 4.0) must be installed prior to the software
installation.

Note: The USB driver is initialized on first connection. The software may not respond for a few
seconds at this time.

35

«
...
39
40
41
42
43
...
»

Содержание AE20218

















































Отзывы:

Нет отзывов

Похожие инструкции для AE20218

Бренд: rainforest Страницы: 2

Бренд: Van Walt Страницы: 2

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: Keller Страницы: 6

Blancett B3100 Series

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 26

Бренд: Badger Meter Страницы: 48

Бренд: F&F Страницы: 2

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Network Card-MS

Бренд: Eaton Страницы: 26

Бренд: QUNDIS Страницы: 20

Бренд: R&S Страницы: 2

Бренд: Hammond Страницы: 78

Бренд: CONDTROL Страницы: 8

Бренд: marposs Страницы: 58

Бренд: Motortech Страницы: 142

Бренд: Analog Arts Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды