AS MOTOR AS 800 FreeRider Скачать руководство пользователя

Страница: 35 / 40

Uneven cut, lawn be-
comes unsightly

Blade is dull or worn.

Have blade resharpened and balanced
by an authorised service centre. Re-
place a damaged blade immediately.

Speed is too high proportion-
ately to the cutting height.

Reduce speed and/or select the correct
cutting height.

Housing of the mower is heavily
contaminated.

Clean.

Different tire pressure.

Check the tire pressure.

Mower housing is not parallel to
the ground.

Adjust (authorised service centre).

Mulching result with
high plant material
not satisfactory

Speed is too high.

Reduce speed.

Mulching result with
low plant material not
satisfactory

Plant material is ejected too
quickly.

Increase speed.

Housing is jammed

Mowed grass was too long or
too damp.

Adjust cutting height and mowing speed
to the mowing conditions.

Blade is worn.

Authorised service centre.

Engine speed is too low despite
full power.

Authorised service centre.

The device does not
stop when the brake
is activated

Brake is adjusted incorrectly,
worn, or defective.

Check the parking brake (see Mainten-
ance). Authorised service centre.

The engine does not
switch off

Switching off system is defect-
ive.

Close the fuel valve.
Authorised service centre.

The tires become flat

Thorns or sharp objects dam-
age the tires.

If necessary, use tire protection gel (au-
thorised service centre).

Содержание AS 800 FreeRider









































Результаты поиска

Содержание AS 800 FreeRider

Отзывы:

Похожие инструкции для AS 800 FreeRider

Бренды по названию

Популярные бренды

AS MOTOR AS 800 FreeRider, Руководство оператора

Результаты поиска

Содержание AS 800 FreeRider

Отзывы:

Похожие инструкции для AS 800 FreeRider

Бренды по названию

Популярные бренды