manualshive.com logo in svg

AS MOTOR Allmaher AS 21 4T B&S, Руководство оператора

Поделиться
Скачать
AS MOTOR Allmaher AS 21 4T B&S Скачать руководство пользователя страница 13

13

Control elements

AS 21 4T B&S

B

A

AS 21 4T Comfort

C

A

B

D

Fig. 5:

Drive lever (A )

With the drive lever, you switch the drive on
and off.

I

0

Drive on (I):
Press the lever towards
the handlebar and con-
tinue to hold.

Drive off (0):
Release the lever.

Engine brake lever (B)

The engine brake lever is a protection device.
When you release the lever, the engine shuts
down immediately, the blade comes to a
standstill within 7 seconds.

M

I

0

Blade/engine on (I):
Press the lever towards the
handlebar and continue to
hold.

Blade/engine off (0):
Release the lever.

Fuel valve

2

1

1: Closed

2: Open

Lever for lateral adjustment of
handlebar (C) 
(only AS 21 4T Comfort)

1. Release the eccentric tension lever.

2. Attention: Do not crush the Bowden cables

when pivoting the handlebar.
Swivel the handlebar to the side to the de-
sired position.

3. Clamp the handlebar with the eccentric ten-

sion lever.

Lever for height adjustment of
handlebar (D) 
(only AS 21 4T Comfort)

1. Pull the tie rod (D) (only AS 21 4T Comfort)

backwards and move the guide bar to a po-
sition that is comfortable to you.

For your device, a retrofit service and parking
brake are available. It is actuated by pulling the
hand lever located at the handlebar and acts
on the rear wheels.

At your request, your dealer will be happy to in-
stall the brake.

Содержание Allmaher AS 21 4T B&S





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды