ARS Automation FlexiBowl 350 Скачать руководство пользователя страница 64

Страница: 64 / 84

7-6

Instructions for use and warnings

CHAPTER 7 - Maintenance

7.2.2

Replacing the FlexiBowl

belt

The FlexiBowl

belt must be replaced according to the following frequencies:

•

at every format change:

each component format may require a different belt surface to be used;

•

every 3 months

: the belt should be replaced every 3 months if used with particularly sharp components;

•

yearly

: in any case, it is recommended to replace the belt at least once a year.

Proceed as follows to

replace the belt of the FlexiBowl

Step

Action

Picture

Unscrew the flange fixing screws with an Allen key.

Remove the flange.

Remove the belt and replace it.

Fit a new belt on and tighten the fixing screws to 10 Nm.

Содержание FlexiBowl 350





















































































Результаты поиска

Содержание FlexiBowl 350

Отзывы:

Похожие инструкции для FlexiBowl 350

Бренды по названию

Популярные бренды

ARS Automation FlexiBowl 350, Инструкция по эксплуатации

Результаты поиска

Содержание FlexiBowl 350

Отзывы:

Похожие инструкции для FlexiBowl 350

Бренды по названию

Популярные бренды