background image

Instruction Manual of PR5534-01 Model Controller

          

2010-12-01                   N0

VER1.1 

 

                             

  - 

safety during using, please read the following items carefully before using

 

1.  The end user should carry on the load installation strictly according to the wiring 

diagram and parameters. 

2.  The ground wiring should be connected to the normal-running supply circuits, so as for 

the steaming. 

3.  The end user should use power supply cables in 3 x 3mm

2

  or wider cable diameter. 

According to the National standards (GB). The socket should be of 30A or above 

according to the National standards (GB). 

4.  The end user should install air-break or leakage switch of 30A or above according to 

the National standards (GB). 

5.  Please check strictly the wire of input water pipe, steaming pipe, power box and control 

box. After confirming every part is OK, then you can start the shower device.

specially, 

make sure all operation should keep inside water.

 

6.  The steaming device and power box cannot be installed in the sauna shower; it should 

be installed according to the instruction on the shell. 

7.  The inner hole of steam input pipe should be above 15mm; installing valve in the 

output pipe is forbidden. 

8.  Please do not install the equipments of bad quality that manufactured by illegal 

factories to the steaming device; Disassembling, changing the fixed inner wiring or 

connect some wiring to the power box are forbidden. 

9.  The water quality should comply with the local water standards. 

10.  During installation, connect drainage pipe to the steaming device and lead the water 

our-side of the shower. It’s better to install a filter to the input so as to prolong the 

lifetime. 

11.  In the hard-water area, please wash the steaming device and remove the dirt 

periodically. The special water level sensor is probe (indicated by label on the 

steaming device surface). Normally, the user should check every 3 months and do the 

washing according to the practical condition. Suggesting washing methods: dilute 

5~10gs of citric acid with 1.4 liters of water, disassemble the connection pipes of 

Содержание 6100











Отзывы: