Arrow Storage Products PC1010 Скачать руководство пользователя страница 24

Страница: 24 / 24

PC1010 PC1010EU

1. Avoid nicking or scraping the coating surface,

inside and out.

2. Keep roof and post perimeter free of debris and

leaves which may accumulate and retain moisture.

These can do double damage since they give off

acid as they decay.

3. Touch up scrapes or nicks and any area of visible

rust as soon as possible. Make sure the surface is

free of moisture, oils, dirt or grime and then apply

an even fi lm of high quality touch-up paint.

SOME FACTS ABOUT RUST

Rusting is a natural oxidizing process that occurs

when bare metal is exposed to moisture. Problem

areas include screw holes, unfinished edges, or

where scrapes and nicks occur in the protective

coating through normal assembly, handling and use.

Identifying these natural rusting problem areas and

taking some simple rust protection precautions can

help to stop rust from developing, or stop it quickly

as soon as it appears.

705220511

DC24

Содержание PC1010

























Результаты поиска

Содержание PC1010

Отзывы:

Похожие инструкции для PC1010

Бренды по названию

Популярные бренды

Arrow Storage Products PC1010, Руководство пользователя и инструкции по сборке

Результаты поиска

Содержание PC1010

Отзывы:

Похожие инструкции для PC1010

Бренды по названию

Популярные бренды