background image

   

  

!

2

!

 

Imprint 

Copyright © 2018 Arnold & Richter Cine Technik GmbH & Co. Betriebs KG.  

All rights reserved.  

No parts of this document may be reproduced without prior written consent of Arnold & Richter Cine 

Technik GmbH & Co. Betriebs KG. Specifications are subject to change without notice. Errors, 

omissions, and modifications excepted. ARRI, ALEXA, AMIRA, LDS and LENS DATA SYSTEM are 

trademarks or registered trademarks of Arnold & Richter Cine Technik GmbH & Co. Betriebs KG.  

All other brands or products are trademarks or registered trademarks of their respective holders and 

should be treated as such. Original version.  

For further assistance: 

Arnold & Richter Cine Technik GmbH & Co. Betriebs KG 

Türkenstr. 89 

80799 München 

Germany  

www.arri.com

Document revision history

Version 

 

Order Coder 

 

Release 

 

Date 

3.1.0.2 

 

K4.0019240  

 

F06606 

 

29. Jan 2018

3.1.0.1 

 

 

 

 

 

 

 

 

01. Oct 2017

Scope 

The third generation of the MAXIMA and TRINITY graphic user interface, the so called 

GUI

 can be 

used with all exiting MAXIMA and TRINITY units. The redesigned graphic user interface is focusing 

on easy use of the software and a fast setup of the MAXIMA and TRINITY. 

Disclaimer

Before using the products described in this manual, be sure to read and understand all the respective 

instructions.  

Otherwise the customer must contact ARRI before using the product.  

While ARRI endeavors to enhance the quality, reliability and safety of their products, customers agree 

and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimise the 

risk of damage to property or injury (including death) to persons arising from defects in the products, 

customers must incorporate sufficient safety measures in their work with the system and heed the 

stated conditions of use.  

ARRI or its subsidiaries do not assume any responsibility for losses incurred due to improper handling 

or configuration of the TRINITY or other system components.  

ARRI assumes no responsibility for any errors that may appear in this document. The information is 

subject to change without NOTICE.  

For product specification changes after this manual was published, refer to the latest published ARRI 

data sheets or release notes, etc., for the most up-to-date specifications. 

Not all products and/or types are available in every country. Please check with an ARRI sales 

representative for availability and additional information. Neither ARRI nor its subsidiaries assume any 

liability for infringement of patents, copyrights or other intellectual property rights of third parties by or 

arising from the use of ARRI products or any other liability arising from the use of such products. No 

license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual 

property right of ARRI or others.  

ARRI or its subsidiaries expressly exclude any liability, warranty, demand or other obligation for any 

claim, representation, cause, action, or whatsoever, express or implied, whether in contract or not, 

including negligence, or incorporated in terms and conditions, whether by statue, law or otherwise. In 

no event shall ARRI or its subsidiaries be liable for or have a remedy for recovery of any special, 

direct, indirect, incidental, or consequential damages, including, but not limited to lost profits, lost 

savings, lost revenues or economic loss of any kind or for any claim by a third party, downtime, good-

will, damage to or replacement of equipment or property, any cost or recovery of any material or 

goods associated with the assembly or use of our products, or any other damages or injury of the 

persons and so on or under any other legal theory.  In the event that one or all of the foregoing 

clauses are not allowed by applicable law, the fullest extent permissible clauses by applicable law are 

validated. 

Imprint

Содержание MAXIMA





























Отзывы: