It is recommended to clean the threads and O-ring off dirt and old grease. Remember that secure protection
from water and dust cannot be provided by worn out sealing and fouling as well as lack of lubricant cause fast
wear-out of threads and sealing rings.
To clean the thread do the following:
1.
Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal
things as it can damage the ring).
2.
Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is
worn out or damaged replace it by a new one.
3.
Clean the metal threads with a brush using ethanol. Be careful not to allow applied liquid to get inside
the flashlight or tailcap as it can cause fails in functionality of the flashlight.
After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel
760G. The application of automotive and other improper grease can cause swelling and damage of the sealing
rings.
In case of active operation and application in dusty environments it is recommended to perform cleaning and
lubricating of the parts as often as required, even if it is more than twice a year.
Service and Warranty
Armytek Optoelectronics Inc.
Web: www.armytek.com Email: [email protected]
Address: 67 Vandervoort Dr, Richmond Hill, Ontario, L4E 0C7, Canada
Specifications are subject to change without notice.
Armytek Predator flashlights have several operational modes:
Main – permanently switched light at High brightness (full pressing of the button with the head of the
flashlight tightened). It's an easy and comfortable operational mode for Hunters, especially when the
flashlight is used with remote switch.
Additional – permanent switched light at Middle, Low and Lower Low brightness at user's choice (full
pressing of the button with the head of the flashlight loosen).
Tactical – High, Middle, Low and Lower Low brightness switched by half-pressing of the button and active
till the button is released. Suitable for giving signals by short button pressings.
Main Mode Operation:
1.
Tighten the head of the flashlight if
it is loosened.
2.
First full pressing of the button (to
the click) turns the light on.
3.
Second full pressing turns it off.
1.
2.
õ2
Armytek provides free warranty repair for 10 years from the purchase.
Warranty doesn't cover damage caused by:
1.
Improper usage.
2.
Attempts to modify or repair the flashlight by nonqualified specialists.
3.
Longtime application in chlorinated or polluted water, or other liquids (other than water).
4.
High temperatures and chemicals' exposure, including the liquid from defected batteries.
5.
Usage of low-quality batteries.
Tactical Mode Operation:
1.
For tactical activation use half-
pressing of the button (no click!).
2.
To access the High brightness
level the head of the flashlight
must be tightened, to access other
levels it must be loosened.
3.
The light remains on while you half
press the button.
Armytek
Predator
USER MANUAL
Thank you for choosing the products of
Armytek Optoelectronics Inc.,
Canada.
Please read this manual carefully before using the flashlight.
www.armytek.com
Care and Storage
Operation
In case the rubber button is damaged, it should be replaced.
Replacement order:
1.
Unscrew the tailcap.
2.
Unscrew the thread ring gage, which holds the rubber button in the cap.
To do so you should use needle-nose pliers (round-nose pliers or
another tool: most suitable will be expansion pliers). Use the tool as it is
shown at the picture.
Do not disassemble the flashlight except for unscrewing the thread ring gage and
replacing the rubber button. There are no other parts in the flashlight that can be
replaced by the user.
The most technically advanced flashlights in the world.
Born to exceed
Born to exceed
The most technically advanced flashlights in the world.
Additional Mode Operation
:
1.
If the head of the flashlight is
tightened, loosen it for 1/8 of a
circle.
2.
First full pressing of the button (to
the click) turns the light on at
Lower Low brightness.
3.
To switch the brightness level turn
the flashlight on and off by full
pressing.
4.
The brightness levels switch
cyclically: Lower Low - Low -
Middle.
