Armeka Engineering AE-780 Скачать руководство пользователя

Страница: 10 / 13

AE-780 Operation Manual

Rev. 11/30/12 MKB

XAMPLE OF

EASURING

RTG

ISSIPATIVE

ABLE

ATS

A. To test RTG on a workstation, connect the first lead to the meter and to a 5

probe. Place the probe on the work surface. Connect the second lead to the meter
and to a groundable point (RTGP).

B. To attach lead to RTGP, slip the alligator clip to the lead and connect it to the ground

snap or connect the banana plug to a common point ground plug:

b. Press the “TEST” button and the value will be displayed on the LED. While

performing test, do not touch lead wires or probe. Avoid overlapping of lead wires.
This will ensure accurate readings.

c. Resistance values are in ohms. When recording test values also make

note of the temperature and humidity, as the environment can affect test
results.

Eastern Energy Co., Ltd.

Tel: 66-3844-6117

40/4 Vitoondumri Rd., Banbueng

Page 10 of 13

[email protected]

Banbueng, Chonburi, Thailand

www.eastern-energy.com

www.eastern-energy.net

Содержание AE-780














Результаты поиска

Содержание AE-780

Отзывы:

Похожие инструкции для AE-780

Бренды по названию

Популярные бренды

Armeka Engineering AE-780, Руководство по эксплуатации

Результаты поиска

Содержание AE-780

Отзывы:

Похожие инструкции для AE-780

Бренды по названию

Популярные бренды