ARM V2M-Juno r2 Скачать руководство пользователя страница 97

Страница: 97 / 150

Table 4-13 SYS_PCIE_CNTL Register bit assignments

Bits

Name

Function

[31:2]

Reserved. If you write to this register,
you must write all zeros to these bits. If
you read this register, you must ignore
these bits.

[1]

PCIE_RSTHALT

Error signal from PCIe switch.

[0]

PCIE_nPERST

Reset signal to PCIe expansion slots.

Related concepts

4.3.1 APB system register summary

on page 4-89

4.3.11

SYS_PCIE_GBE Register

The SYS_PCIE_GBE Register characteristics are:

Purpose

Contains the 48-bit PCI Express Ethernet MAC address.

Usage constraints

Bits[47:0] are read-only.

Configurations

Available in all V2M-Juno r2 motherboard configurations.

The following figure shows the bit assignments.

SYS_PCIE_GBE_L

SYS_PCIE_GBE_H

Reserved

48 47

Figure 4-12 SYS_PCIE_GBE Register bit assignments

The following table shows the bit assignments.

Table 4-14 SYS_PCI_GBE Register bit assignments

Bits

Name

Function

[63:48]

Reserved. If you read this register, you
must ignore these bits.

[47:32]

SYS_PCIE_GBE_H

Most significant 16 bits of the PCI
Express Ethernet MAC address.

[31:0]

SYS_PCIE_GBE_L

Least significant 32 bits of the PCI
Express Ethernet MAC address.

Related concepts

4.3.1 APB system register summary

on page 4-89

4.3.12

SYS_PROC_ID0 Register

The SYS_PROC_ID0 Register characteristics are:

Purpose

Identifies the active clusters in the Juno r2 SoC.

Usage constraints

There are no usage constraints.

4 Programmers Model

4.3 APB system registers

ARM 100114_0200_03_en

4-97

Non-Confidential

Содержание V2M-Juno r2























































































































































Результаты поиска

Содержание V2M-Juno r2

Отзывы:

Бренды по названию

Популярные бренды

ARM V2M-Juno r2, Техническое справочное руководство

Результаты поиска

Содержание V2M-Juno r2

Отзывы:

Бренды по названию

Популярные бренды