manualshive.com logo in svg

ARM Prospector P1100, Руководство пользователя, Страница: 98 / 154

Поделиться
Скачать
ARM Prospector P1100 Скачать руководство пользователя страница 98

Programmer’s Reference

4-12

Copyright © ARM Limited 2000. All rights reserved.

ARM DUI 0122A

4.2.6

LCD controller registers

This set of registers is used to configure and control the display interface. These are set 
up by ARM Firmware Suite, where appropriate. Detailed descriptions of these registers 
can be found in the Intel StrongARM SA-1100 Microprocessor Developer’s Guide

4.2.7

DRAM banks

The P1100 provides two areas of DRAM which are located within the DRAM bank 
select 0 and 1 regions. These are used for general purpose data storage or for storing 
screen-image data. The DRAM configuration register must be set up correctly to 
support the size and memory device configuration for each bank, as shown in Table 4-7 
(refer to the Intel StrongARM SA-1100 Developer’s Manual). 

Table 4-6 LCD control registers

Address

Register

Notes

0xB010 0000

LCD controller control register 0

0xB010 0004

LCD controller status register

0xB010 0010

DMA channel 1 base address register

0xB010 0014

DMA channel 1 current address register

0xB010 0018

DMA channel 2 base address register

0xB010 001C

DMA channel 2 current address register

0xB010 0020

LCD controller control register 1

0xB010 0024

LCD controller control register 2

0xB010 0028

LCD controller control register 3

Table 4-7 DRAM bank addresses

Base address

Bank

Configuration

0xC0000000

DRAM bank 0

Both banks are 16MB using 4Mword x 16bit 
devices in 12x10 configuration. Refresh 
period of 128ms. 

0xC8000000

DRAM bank 1

Содержание Prospector P1100



























































































































































Отзывы:

Нет отзывов