manualshive.com logo in svg

Arlyn Scales MKE-5, Руководство по настройкам

Поделиться
Скачать
Arlyn Scales MKE-5 Скачать руководство пользователя страница 22

 

22 

ON/OFF key again and wait. After the weight appears on screen, the message “Starting QuickConnect” appears on the top 
part of the screen. Then you will see “Verifying Service”. After this message, you will see “Link Established. This means the 
QuickConnect session was successful. If you see “Service Check Failed!” and “Device not found”, this means the 
QuickConnect device is not in the vicinity, or in more advanced setting, the Local/Remote port is not right. If the session was 
successful, the Bluetooth indicator will appear. Press PRINT key to send data to the device. 

 
Manual 

For a manual operation, 

press ON/OFF and then press 5 (within 3 seconds)

. Immediately, the scale will scan the current 

area to see if the device you defined in the Quick Connect screen is present. If it is present, it will connect to this device and 
show the Bluetooth indicator. If the device is not found, then the appropriate status message will be shown. You may now 
send and receive data from the device. Press PRINT key to send data to the device. 

Quick Disconnect 

If you want to disconnect from the device, you can either use the Quick Disconnect feature or go to the Bluetooth Setup 
option and disconnect from there. To quick disconnect the device, use the same sequence that is described above; i.e. 

press ON/OFF and then press 5 (within 3 seconds)

. This quick disconnection sequence can also be used if you have 

connected to the device without going through Quick Connect.  

Bluetooth Local Settings (ADVANCED) 

This section introduces some of the advanced features available for the scale Bluetooth module. Most of these features 
have to do with the local configuration of Bluetooth module. It is recommended that you are well versed with the above 
described operation before you get into this section. Most of the time, you will not need to modify these settings. 
 
Following are the local Bluetooth settings that can be modified to satisfy some specific requirements in your application. To 
access these settings, in the Bluetooth Setup screen, scroll down “Bluetooth Local Settings.”  

 

Bluetooth Enable 

This menu option allows you to Enable or Disable the Bluetooth functionality. After toggling this option, the scale needs to be 
restarted.  

View Device Info 

This menu option allows to view the Bluetooth modules name and device address. 

Change Local Name 

This menu option allows you to change the local name of the scale Bluetooth module. Currently, it is defaulted 

to “ARLYN 

SCALE”. You can modify this to anything you want depending on your needs.  

Virtual Port Settings 

This menu option specifies the characteristics of the aerial Virtual COM port through which to send out data. This setting, if 
changed improperly, may disable your Bluetooth communication system. 

Fixed Pin Settings 

This shows the current Default Pin settings of the Bluetooth module. This allows the Bluetooth module to send this pin to any 
device asking for a pin request. You will never need to enter the pin on the scale.  
 
Entering this option, the default pin is shown on screen. The default pin is ‘0000’. You can press ENTER to change the 
default pin. You have two options here: 
 

1. 

Default Fixed Pin:

 You can put a default pin, of up to 16 alphanumeric characters in length. The next time a pairing is 

needed, this pin has to be entered on the other remote device when a dialog box pops up. 

2. 

No Fixed Pin:

 By pressing ENTER without entering a pin, the scale will assume that you want to enter the pin each 

time a pairing is required. The next time you pair with a device, a dialog box will pop up on the scale screen for you 
to enter a desired pin. That same pin has to be entered in the remote device as well. 

Содержание MKE-5

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды