Arlyn Scales MKE-5 Скачать руководство пользователя страница 17

 

17 

Data Logging  

The optional USB Data Logger module allows a large amount of data from your scale to be recorded into a USB Flash Drive. 
The Flash Drive maybe removed from the scale and inserted into a standard USB port on a PC. The data is collected on a 
.CSV file (comma-separated values), which can be opened using any spreadsheet software such as Microsoft Excel®. 
 
Data Logger is activated by default. To activate/deactivate it, press 

Menu -> Option Setups -> Data Logging. 

On the 

horizontal menu displayed in the Data Logging setup screen, select ACTV to activate/deactivate Data Logging. 

Basic Operation  

There are two modes of operation for using the USB Data Logger: 
 

Triggered

 

– The weight entry is written to the USB when the user presses a button 

Continuous

 

– The weight entry is written to the USB at regular time intervals selected by the user. 

 
To switch modes of operation, on the Data Logging setup screen select TYPE on the horizontal menu to switch between 
triggered and continuous type logging. 
 
In Triggered Mode, press the TWO (2) key each time to log the current weight and time on the USB drive. This will be noted 
by a “Recording Entry” message on the status message area of the screen each time the TWO key is pressed. 
 
In Continuous Mode, press the TWO key to begin the data logging sequence. A “Data Logging On” message will be 
displayed in th

e status area, followed by the “Recording Entry” message after the time interval has passed. After that, 

“Recording Entry” message will appear on regular time intervals specified by the user. The time interval can be set in the 
Data Logging setup screen. Select the TIME option on the horizontal menu to enter the time interval in seconds. 

Note about Multiple Platforms 

For Multiple platform, when the scale is in the Multiple Platform screen (where all the platforms are viewed at the same time 
with a TOTAL), the TWO key is already occupied for switching between platforms. Instead, press the SHIFT key (ON/OFF) 
and then the ENTER 

key in succession. Please make sure to see the “Shft” notification on the top left corner of the screen 

before pressing the ENTER key. The ENTER key may have to be held a half-a-

second longer to register the “Recording 

Entry” notification. 
 
The SHIFT+ENTER key-sequence will have the same effect as the TWO key described above in the Basic Operation 
section. 

USB Flash Drive Use 

Your Data Logging scale comes with a 1 Gigabyte (1 GB) USB flash drive that can hold more than 4 million readings! For 
those scales equipped with Data Loggers, the scale will always test the Data Logger system and check for a USB flash drive 
at power up. If a USB Flas

h drive is plugged in, the scale will show the message “USB Stick found…” and if the USB flash is 

not plugged in, then the message will simply say, “USB Stick not found…”. At times, the scale may show “USB Stick not 
found…” even when a USB flash drive is plugged in. In this case, simply recycle the power and it should initialized the Data 
Logger system correctly. 
 
If the USB flash drive has never been used with the scale, the scale software will create the file DATA.CSV automatically. 
This is the file the scale uses to store the weight entries. When recording new data on a card that already contains the file, 
the scale will look for the file and append the new weight entries to the end. This file can then be opened using Microsoft 
Excel® or a text editor. 
 
It is okay to remove the USB drive while the scale is on. But if the user wants to plug in the USB drive back again, the user 
has to: 
Shut off the scale, 
Plug in the USB drive, 
Wait for 5 seconds  
Turn on the scale.  
 
The USB drive cannot be plugged in while the scale is on since the USB Data Logging system initialization routine happens 
only at power up. But there is no harm if the USB drive is plugged in while the scale is on and an attempt is made to write 
data into it. In this case, the status message wi

ll display “Recording Entry”, followed by “Can’t Open File…” This means that 

the file DATA.CSV cannot be opened at this time. 

Содержание MKE-5

























Отзывы: