The Max function is deactivated even if there is a stall error, if the “OFF” status is engaged or if the +/– buttons are
pressed to change the set-point.
Setting the set-point
By pressing the PLUS or MINUS buttons, the user can choose the set-point temperature (indicated by the temperature
LEDs, with the other LEDs off ). Each press of the button increases or decreases the set temperature by 10 degrees. After
5 seconds without any action, the set-point will be confirmed and memorised.
STALL STATUS
There are two possible stall statuses:
- TOUCH CONTROL STALL STATUS
If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled. This status
is indicated by the flashing of the temperature LEDs (fast if the product is on, slow if it is off ).
- OTHER STALL STATUS
If other errors are detected, all the LEDs will start flashing.
To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on
and off. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the
ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the
Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for
5 seconds.
USEFUL INFORMATION (for the user)
Before any operation of cleaning the device make sure to turn off the product by bringing the external switch to the
OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic
material.
If the water delivery is cold, have the following checked:
- that the device is connected to the power supply and the external switch is in the ON position.
- that at least led 40°C (1 fig. 3) is turned on.
If there is presence of steam output from the taps:
Remove power from the electrical appliance and contact technical support.
If the hot water delivery is insufficient, have the following checked:
- the pressure of the water mains;
- eventual obstruction of the inlet and outlet pipes (deformation or sediment).
IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE
BY A QUALIFIED TECHNICIAN.
The indicated data and specifications are not binding; the manufacturer reserves the right to modify them at his
own discretion notification or replacement.
This product conforms to Directive WEEE 2012/19/EU.
The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the prod-
uct must be scrapped separately from other waste at the end of its service life. The user must therefore
hand the equipment over to a sorted waste disposal facility for electro-technical and electronic equipment
at the end of its service life.
Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.
Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area
is at least 400 m2 for disposal free of charge and without any obligation to purchase new product.
EN
18
Setting the set-point
By pressing the PLUS or MINUS buttons, the user can choose the set-point temperature (indicated by the temperature
LEDs, with the other LEDs off). Each press of the button increases or decreases the set temperature by 10 degrees. After
5 seconds without any action, the set-point will be confirmed and memorised.
STALL STATUS
There are two possible stall statuses:
- TOUCH CONTROL STALL STATUS
If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled.
This status is indicated by the flashing of the temperature LEDs (fast if the product is on, slow if it is off).
- OTHER STALL STATUS
If other errors are detected, all the LEDs will start flashing.
To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on
and off. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the
ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the
Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for
5 seconds.
USEFUL INFORMATION (for the user)
Before any operation of cleaning the device make sure to turn off the product by bringing the external switch to the
OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic
material.
If the water delivery is cold, have the following checked:
- that the device is connected to the power supply and the external switch is in the ON position.
- that at least led 40°C (1 fig. 3) is turned on.
If there is presence of steam output from the taps:
Remove power from the electrical appliance and contact technical support.
If the hot water delivery is insufficient, have the following checked:
- the pressure of the water mains;
- eventual obstruction of the inlet and outlet pipes (deformation or sediment).
Water trickling from the pressure safety device
During the heating phase, some water may trickle from the tap. This is normal. To prevent the water trickling, a suitable
expansion vessel must be installed on the flow system. If the trickling continues even after the heating phase, have the
following checked:
- device calibration;
- the pressure of the water mains.
Caution: Never obstruct the appliance outlet!
IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE
BY A QUALIFIED TECHNICIAN.
The indicated data and specifications are not binding; the manufacturer reserves the right to modify them at his
own discretion notification or replacement.
This product conforms to Directive WEEE 2012/19/EU.
The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the product must be
scrapped separately from other waste at the end of its service life. The user must therefore hand the equipment over to a
sorted waste disposal facility for electro-technical and electronic equipment at the end of its service life.
Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.
Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area is at least 400
m
2
for disposal free of charge and without any obligation to purchase new product.
