Ariston 47-116-49 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 80

background image

/

39

BOILER PROTECTION DEVICES

Anti-frost Device.
The anti-frost function acts on the central heating flow tempe-
rature probe, independently from other regulations, when the
electrical supply is turned on.
If the primary circuit temperature is between 3°C and 8°C the
pump will run (with the diverter valve switching between cen-
tral heating and hot water every 1 minute) until the temperature
reaches > 9°C.
If the flow temperature remains between 3°C and 8°C the pump
will continue to run for a maximum of 20 minutes unless a tem-
perature above > 9°C is detected in the central heating flow, af-
ter this the the burner will fire (heating position) until a tempera-
ture of > 30°C is detected.
If the central heating flow temperature is < 3°C, the burner will
fire (heating position) at minimum power until the temperature
reaches > 35°C, the burner will go out.
If lockout is caused by overheat the burner will not fire but the
pump will continue to run (heating position).
The anti-frost device activates only when (with the boiler opera-
ting correctly):
- the system pressure is correct;
- the boiler is electrically powered;
- there is a supply of gas.

Ignition and Detecion

5 01

No flame detected

5 02

Flame detected with gas valve closed

5 04

Flame lift

5 P1

1st Ignition Failed

5 P2

2nd Ignition Failed

5 P3

Flame cut-off

Air Inlet / Flue gas outlet

6 10

Overheat (Main heat exchanger)

6 12

Insufficient fan speed

Multi-zone Heating (Heating Zone Modules - optional)

7 01

Zone 1 send sensor defective

7 02

Zone 2 send sensor defective

7 03

Zone 3 send sensor defective

7 11

Zone 1 return sensor defective

7 12

Zone 2 return sensor defective

7 13

Zone 3 return sensor defective

7 22

Zone 2 overheating

7 23

Zone 3 overheating

7 50

All Heating Zones locked

«
...
37
38
39
40
41
...
»

Содержание 47-116-49

















































































Отзывы:

Нет отзывов

Похожие инструкции для 47-116-49

Бренд: Watts Страницы: 167

Бренд: Saunier Duval Страницы: 15

Бренд: Lochinvar Страницы: 12

Бренд: U.S. Boiler Company Страницы: 9

Бренд: IBC Страницы: 124

Toast-R-Oven Classic TRO300 Series

Бренд: Black & Decker Страницы: 2

Power HT 1.1000

Бренд: Baxi Страницы: 36

Nuvola 3 Comfort

Бренд: Baxi Страницы: 40

EBE Express Series

Бренд: Ecoboil Страницы: 4

EB Rapid Series

Бренд: Ecoboil Страницы: 4

Бренд: Powermatic Страницы: 23

Бренд: KyungDong Страницы: 34

Бренд: Baxi Страницы: 8

Бренд: Baxi Страницы: 40

Бренд: Worcester Страницы: 16

Бренд: Worcester Страницы: 21

Vitogas 050 Rs Series

Бренд: Viessmann Страницы: 32

Бренд: Potterton Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды