Ariens Professional 21 938024-SSR Скачать руководство пользователя страница 13

EN - 11

EMERGENCY STOPPING

1. Release auger control lever.
2. Push engine switch to the stop position.
3. Wait for all moving parts to stop before 

leaving operator’s position.

START THE ENGINE

1. Position discharge chute in a safe 

direction. See 

Position Discharge Chute

 

on page 11.

2. Turn fuel valve to the on position.
3. Push engine switch to run position.
4.

Cold Engines Only:

 Turn choke control 

knob to on position. 

5.

Cold Engines Only:

 Push primer bulb 

twice.

6. Pull recoil starter handle.

a. Grasp handle and pull rope out slowly 

until it pulls harder.

b. Pull handle firmly and quickly with a 

rapid, continuous full-arm stroke. 
Repeat until engine starts. If engine 
does not start, see 

Troubleshooting

 

on page 19.

c. Let handle rewind slowly after engine 

starts. DO NOT let handle snap back 
against handlebar.

7. Gradually turn choke off as engine 

warms.

OPERATE UNIT

1. Rotate discharge chute and move 

deflector to desired positions. See 

Position Discharge Chute

 on page 11.

NOTICE: 

On some surfaces, auger paddle 

rotation may leave residual paddle material. 
This usually washes off after rain showers.
2. Engage auger control lever to clear snow 

and move unit forward. Release bar to 
stop augers and unit. See Figure 10.

IMPORTANT: 

If unit does not propel itself 

forward in heavy snow or on slippery 
surfaces, push forward on the handlebar. 
Allow unit to work at its own pace.

IMPORTANT: 

Disengage auger when 

traveling between work areas.

3. Move handlebar left and right to steer 

unit.

4. Reposition discharge chute and deflector 

as necessary.

Position Discharge Chute

IMPORTANT: 

Always throw snow in a safe 

direction, away from people and windows.

NOTICE: 

If chute becomes frozen and does 

not turn correctly, move unit into warm area 
until controls are unfrozen.
See Figure 11.
1. Release auger control lever.
2.

Model 938025:

 Move discharge chute 

rotation lever left or right to rotate chute.

Model 938024:

 Move discharge chute 

rotation handle left or right to rotate chute.

3. Move deflector lever up or down to 

control discharge distance.

OPERATION

WARNING: 

AVOID INJURY. Read 

and understand the 

Safety

 section 

before proceeding.

Figure 10

Содержание Professional 21 938024-SSR



























Отзывы: