background image

GB - 5

SAFETY ALERTS

Look for these symbols to point out important 
safety precautions. They mean:

Attention! 

Personal Safety Is Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal words below are 
used on decals and in this manual.

Read and understand all safety messages.

NOTATIONS

NOTE:  General reference information for proper operation 
and maintenance practices.

IMPORTANT: Specific procedures or information required to 
prevent damage to unit or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working precautions, for 
the benefit of yourself and others. Understand and follow all 
safety messages. Be alert to unsafe conditions and the 
possibility of minor, moderate, or serious injury or death. 
Learn applicable rules and laws in your area, including those 
that may restrict the age of the operator.

REQUIRED OPERATOR TRAINING

Original purchaser of this unit was instructed by the seller on 
safe and proper operation. If unit is to be used by someone 
other than original purchaser; loaned, rented or sold, 
ALWAYS provide this manual and any needed safety 
training before operation.

SAFETY DECALS AND LOCATIONS

ALWAYS replace missing or damaged Safety Decals. Refer 
to figures below for Safety Decal locations.

SAFETY

WARNING: This cutting machine is capable 
of amputating hands and feet and throwing 
objects. Failure to observe the safety 
instructions in the manuals and on decals 
could result in serious injury or death.

Slopes are a major factor related to 
loss-of-control and tip-over accidents. 
Operation on all slopes requires extra 
caution.

Tragic accidents can occur if the operator is 
not alert to the presence of children. Never 
assume that children will remain where you 
last saw them.

Gasoline is extremely flammable and the 
vapors are explosive, handle with care.

Disengage attachment, stop unit and engine, 
remove key, engage parking brake, and allow 
moving parts to stop before leaving 
operator’s position.

DANGER: IMMINENTLY HAZARDOUS 
SITUATION! If not avoided, WILL RESULT 
in death or serious injury.

WARNING: POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, COULD 
RESULT in death or serious injury.

CAUTION: POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, MAY RESULT in 
minor or moderate injury. It may also be 
used to alert against unsafe practices.

Figure 2

1

2

3

4

OG1820

2

Figure 3

2

1

OG2050

2

4

Содержание 988316



























Отзывы: