manualshive.com logo in svg

ARI-Armaturen ARI-PACO 2G 1,6 D, Инструкция по эксплуатации и установке

Поделиться
Скачать
ARI-Armaturen ARI-PACO 2G 1,6 D Скачать руководство пользователя страница 35

0040506004 0919

Page 2-35

Operating and installation instructions

Thrust actuator ARI-PACO

®

 2G 1,6D/Y

7.0  Care and maintenance 

The thrust actuator requires very little maintenance. Accordingly maintenance in specified intervals 
is not necessary.
Remove any externally visible dirt from the actuator and the electronics occasionally, depending on 
the operating conditions.
No liquid must be allowed to come into contact with or get inside the electronics!
Never clean the actuator using liquids or aggressive solvents or agents that are detrimental to 
health or highly flammable.
We recommend dampening a cloth with cleaning agent to clean the actuator rather than applying it 
directly.

8.0  Troubleshooting

In the event of malfunction or faulty operating performance check that the installation and 

adjustment work has been carried out and completed in accordance with these Operating 
Instructions.

If malfunctions cannot be eliminate with the help of the following table

 

„

9.0 Troubleshooting table

“, 

the supplier or manufacturer should be consulted.

9.0  Troubleshooting table

NOTE !

 

The power supply cable must be disconnected from the mains (i.e. deenergised) prior 
to cleaning the electronics. Suitable precautions must be taken to prevent the mains 
voltage from being re-connected inadvertently.

Non-observance can result in death, severe personal injury or substantial property 
damage.

ATTENTION !

 

- It is essential that the safety regulations are observed when identifying faults.

ATTENTION ! 

- read point 10.0 and 11.0 prior to dismantling and repair work !
- read point 6.0 before restarting the plant

Содержание ARI-PACO 2G 1,6 D










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды