manualshive.com logo in svg

ARI-Armaturen ARI-PACO 2G 1,6 D, Инструкция по эксплуатации и установке

Поделиться
Скачать
ARI-Armaturen ARI-PACO 2G 1,6 D Скачать руководство пользователя страница 31

0040506004 0919

Page 2-31

Operating and installation instructions

Thrust actuator ARI-PACO

®

 2G 1,6D/Y

5.5.4.1.5  Operation – Programming / clearing positions 

Fig. 14

Programming

Procedure

Relay 1

- Approach the spindle position. 

- Press "Relay 1 button (up)" until the corresponding LED blinks once. 
- From now on, relay 1 is switched to "active" when the current position is 

overtravelled in the UP direction.

Relay 2

- Approach the spindle position. 
- Press "Relay 2 button (down)" until the corresponding LED blinks once. 
- From now on, relay 2 is switched to "active" when the current position is 

overtravelled in the DOWN direction.

Clear

- Press "Relay 1 button (up)" AND "Relay 2 button (down)" simultaneously 

for longer than one second

- Both LEDs blink once to confirm the new setting. 
- From now on, the two relays are no longer switched.

Overwrite

Similar to Prog. Rel.1 or Prog. Rel.2. 
The new position automatically overwrites the old position.

Test

Move the spindle to and fro with any type of control (e.g. MAN
switch) and watch the LEDs.

"Relay 1" LED (up)

"Relay 1" button (up)

"Relay 2" button (down)

"Relay 2" LED (down)

Содержание ARI-PACO 2G 1,6 D










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды