manualshive.com logo in svg

Argon 18 E-119 TRI, Инструкция по сборке, Страница: 9 / 47

Поделиться
Скачать
Argon 18 E-119 TRI Скачать руководство пользователя страница 9

8

E-119 TRI 233A: 6. Frame Inspection

 

 

Parts installed on the frame                   Description 

Screw Torque  Detail

   

 

type Nm 

   

 

 

1 

Front derailleur hanger 

                Screw (2) 

5mm 

4Nm 

Loctite  

 

2 

Rear derailleur hanger 

                Screw (2) 

3mm  4Nm Loctite

 

3 

Bottle cage 

                Screw (5) 

4mm  3Nm Grease

 

4 

Bottom bracket cover 

                Screw (2) 

4mm  2.5Nm Grease

 

5 

Brake arms pivot (front / rear)                  Screw (2) 

6mm  7Nm Loctite

 

6 

Front brake cap 

                Screw (2) 

4mm  2.5Nm Grease

 

7 

Rear brake cap 

                Screw (2) 

4mm  5Nm Grease

 

IMPORTANT:

The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their

torque specifications.

BEFORE ASSEMBLING YOUR NEW E-119 TRI, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:

1. Brakes and gears cables and housing set

2: Frameset parts checklist (see p.44)

3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)

4: For reference, check serial number and write it on p.1

5: All the necessary bolts (refer to Frameset Parts, p.4)

6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is 

straight

Содержание E-119 TRI
















































Отзывы:

Нет отзывов