manualshive.com logo in svg

Argon 18 E-119 TRI, Инструкция по сборке, Страница: 45 / 47

Поделиться
Скачать
Argon 18 E-119 TRI Скачать руководство пользователя страница 45

E-119 TRI 233A: 17. Parts’ SKUs and Descriptions*

44

No. Name 

Assembled on 

A18 SKU# 

Qty

 

Parts already assembled

  Parts

1.1 

E-119 Tri Frame - 

- 

1

2.1 

E-119 Tri Fork 

- FK.E119T.XS.233A 

1

  

 FK.E119T.S.233A

  

 FK.E119T.M.233A

  

 FK.E119T.L.233A

  

 FK.E119T.XL.233A

3.1 

E-119 Tri Seat Post 

- SP.E119T.233A 

1

1.2 

E-119 Rear Brake Cover (incl. screws)

 

Frame 80277 

1

1.3

 

E-119 Lower Rear Brake Cover

 Frame

 80278

 

1

1.7.1 

Seat Post Collar Base (incl. screws) 

Frame 

80373, 80423 

1

1.7.2 

Seat Post Collar Wedge (incl. screws) 

Frame 

80372, 80422 

1

1.8 

Top Tube Grommet (electronic) 

Frame 80280 

1

1.9 

Top Tube Grommet (mechanical) 

Frame 80281 

1

1.10 

Bottom Bracket Cover (incl. screws) 

Frame 80159 

1

1.11 

Rear Derailleur Cable Stopper 

Frame 80160 

1

1.17 

Front Derailleur Cable Grommet 

Frame 80264 

1

1.19 

Head Tube Protector 

Frame 80495 

2

1.20 

Rear Derailleur Grommet 

Frame 80165 

1

2.2 

E-119 Front Brake Cover 

Fork 80282 

1

2.4 

Stem Cap (incl. screws) 

Fork 80283 

1

2.8 

Steerer 

Fork 

80289(xs/s), 80290(m), 

1

  

 

 

80291(l), 80767(xl) 

 

3.2 

Internal Di2 Battery Support 

Seat Post 

80167 

1 Set

4.1 

Handlebar AHB-7600 

Fork 39278 

1

4.2.1 

Swivel Lower Bracket (incl. square nut) 

Handle Bar 

38916 

2

4.2.2 

Swivel Upper Bracket 

Handle Bar 

38915 

2

1.5 

Front Derailleur Hanger (incl. screws) 

Frame 

38882

 

1

1.6 

Rear Derailleur Hanger (incl. screws)

 Frame 

38883

 

1

 

Botte Cage Screws

 Frame 

38884

 

7

*Except for the frame itself, which is not sold as a spare part, all parts can be ordered by referring to their respective SKU number.

Содержание E-119 TRI
















































Отзывы:

Нет отзывов