manualshive.com logo in svg

Argon 18 E-119 TRI, Инструкция по сборке, Страница: 34 / 47

Поделиться
Скачать
Argon 18 E-119 TRI Скачать руководство пользователя страница 34

E-119 TRI 233A: 11. Rear Brake Installation

33

Rim Width 

Brake Pad 

Max. Tire 

Plunger Pos.  Plunger Pos.  Approx. resulting

(mm)   

Washer 

Size   

“A” Distance  “B” Distance  Pad-to-rim Clearance

21mm 

 1x 

2mm 25 

 9.3mm 

 1.3mm 

 3mm

21mm 

 2x 

2mm 25 

 7mm 

 3.6mm 

 4mm

24mm 

 1x 

2mm 25 

 8.2mm 

 2.4mm 

 3mm

24mm 

 2x 

2mm 25 

 7mm 

 3.6mm 

 2.5mm

28mm 

 1x 

2mm 25 

 7mm 

 3.6mm 

 2.5mm

28mm 

 2x 

2mm N/A 

 N/A 

 N/A 

 N/A

Notes:

1. Max. plunger extension length (”A”) is 10.5mm - or when back end is flush with brake arm head.

2. Resulting pad clearance is measured from center of brake pad.

3. These values consider width of supplied pad; if used with different pad or pad holders, values  

 

    might differ.

4. Always set brake in order to get at least 2mm pad-to-rim clearance.

Recommended Rim and Tire Width and Corresponding Brake Adjustment Settings

B

A

Hex 4mm

brake pad 

adj. plunger

Brake pad

washer

Содержание E-119 TRI
















































Отзывы:

Нет отзывов