manualshive.com logo in svg

Arduino nixie v41, Руководство по эксплуатации

Поделиться
Скачать
Arduino nixie v41 Скачать руководство пользователя страница 22

Anode Control Circuit:

Parts List:

S24

SOCKET 24

OK1

EL817

OK2

EL817

OK3

EL817

OK4

EL817

OK5

EL817

OK6

EL817

R1

1k

R2

1k

R3

1k

R12

1k

R13

1k

R14

1k

R4

2.7k

R5

2.7k

R6

2.7k

R15

2.7k

R16

2.7k

R17

2.7k

 SV3

CONN_ANODE

This circuit controls passing the HV to the anodes of the tubes. The micro-controller multiplexes the 
anodes by turning each of them on it turn for a very short period of time. The software controls the rate of 
the multiplexing and the order in which the anodes are activated.

Notes:

•

The Opto-Isolators fit into the 24 pin socket snugly. Be careful to put them in the right way round. 
The dot denotes pin 1 and should be on the side closest to the micro-controller. All 6 should fit 
perfectly into the 24 pin socket.

•

The Opto-Isolators are socketed because they are sensitive to heat and are easily destroyed if you 
apply too much heat to them. Putting them in a socket means that we don't run the risk of 
destroying them while soldering.

•

If you receive the connector header as a single strip, break off 6 pins for SV3.

Содержание nixie v41









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды