Arctic Cat Bearcat 570 XT Скачать руководство пользователя страница 14

Страница: 14 / 72

ZJ004A



NOTE: When air can no longer be

heard purging from oil pump bleed,
tighten the bleed bolt to 7.5 ft-lb.

3. Start the engine. The warning icon

should go out within five seconds.

4. If the warning icon does not go out,

shut the engine off immediately and

repeat step 2; then repeat step 3.

If the warning icon does not go out or if

the engine does not start, take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer. If not under warranty, this

service is at the discretion and expense of

the snowmobile owner.

Indicator Icons (Deluxe

Gauge)

Certain models (TZ1 LXR/LTD models)

are equipped with a deluxe gauge combi-

nation speedometer/tachometer. Indicator

icons are incorporated within the speed-

ometer/tachometer. Also incorporated into

the speedometer/tachometer is a digital

readout screen.

FZ001A

A. High Beam
B. Oil Pressure/Low Oil

C. Coolant Temperature
D. Increment Button
E. Select Button
F. Decrement Button
G. Service
H. Charging System

RPM/MPH (kph)

By pushing the increment button once,

the RPM and MPH will be displayed

(one on the readout screen and one with

the needle). By pushing the button once

again, the functions will be reversed.
By pushing the increment button (with

speed being displayed) for more than two

seconds, the display will change between

standard mph or metric kph.
With RPM displayed on the readout

screen by pushing and holding the incre-

ment button, maximum RPM will be dis-

played on the readout screen. The

maximum RPM readout will reset when

the decrement button is pushed (while

maximum RPM is displayed).

Odometer/Trip-Meter (1)/

Trip-Meter (2)/Hour-Meter

By pushing the decrement button, the

readout screen will display odometer,

trip-meter (1), trip-meter (2), and hour-

meter. To reset the trip meter with the trip

meter displayed, push and hold the decre-

ment button until the display is cleared.

The hour-meter readout will not reset.

Clock/Altimeter

By pushing the select button, the readout

screen will display clock, altimeter, and

maximum altimeter.
With clock selected on the display by

pushing and holding the select button for

two seconds, the option of selecting the

12-hour or 24-hour clock mode is avail-

able. Push the increment button to toggle

between the 12-hour display and the 24-

hour display. When desired mode is dis-

played, push the select button.

CAUTION

Do not attempt to start the engine
with the bleed bolt open.

Содержание Bearcat 570 XT









































































Результаты поиска

Содержание Bearcat 570 XT

Отзывы:

Похожие инструкции для Bearcat 570 XT

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 XT, Руководство оператора

Результаты поиска

Содержание Bearcat 570 XT

Отзывы:

Похожие инструкции для Bearcat 570 XT

Бренды по названию

Популярные бренды