manualshive.com logo in svg

Arctic Cat 500H1, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 500H1 Скачать руководство пользователя страница 26

2-16

Driveshaft/Coupling

The following drive system components should be

inspected periodically to ensure proper operation.

A. Spline lateral movement (slop).

B. Coupling cracked, damaged, or worn.

Suspension/Shock 

Absorbers/Bushings

The following suspension system components should

be inspected periodically to ensure proper operation.

A. Shock absorber rods not bent, pitted, or damaged.

B. Rubber damper not cracked, broken, or missing.

C. Shock absorber body not damaged, punctured,

or leaking.

D. Shock absorber eyelets not broken, bent, or

cracked.

E. Shock absorber eyelet bushings not worn, dete-

riorated, cracked, or missing.

F. Shock absorber spring not broken or sagging.

Nuts/Bolts/Cap Screws

Tighten all nuts, bolts, and cap screws. Make sure riv-

ets holding components together are tight. Replace all

loose rivets. Care must be taken that all calibrated

nuts, bolts, and cap screws are tightened to specifica-

tions (see Section 1).

Ignition Timing

„

NOTE: The 700 EFI rotor/flywheel does not have

timing marks; therefore, timing cannot be verified.

The ignition timing cannot be adjusted; however, veri-

fying ignition timing can aid in troubleshooting other

components. To verify ignition timing, use the follow-

ing procedure.

1. Attach the Timing Light to the spark plug high ten-

sion lead; then remove the timing inspection plug

from the left-side crankcase cover.

2. Using the Tachometer, start the engine and run at

1500 RPM; ignition timing should be 10° BTDC.

3. Install the timing inspection plug.

If ignition timing cannot be verified, the rotor may be

damaged, the key may be sheared, the trigger

coil/CKP sensor bracket may be bent or damaged, or

the CDI unit/ECU may be faulty.

Headlights/Taillight- 

Brakelight

Rotate the ignition switch to the lights position; the

headlights and taillight should illuminate. Test the

brakelight by compressing the brake lever. The brake-

light should illuminate.

HEADLIGHTS

„

NOTE: The bulb portion of a headlight is fragile.

HANDLE WITH CARE. When replacing a headlight
bulb, do not touch the glass portion of the bulb. If
the glass is touched, it must be cleaned with a dry
cloth before installing. Skin oil residue on the bulb
will shorten the life of the bulb.

To replace a headlight bulb, use the following proce-

dure.

1. Remove the wiring harness connector from the

back of the headlight.

2. Grasp the bulb housing, turn it counterclockwise,

and remove the bulb.

3. Install the new bulb into the housing and rotate it

completely clockwise.

4. Install the wiring harness connector.

TAILLIGHT-BRAKELIGHT

To replace the taillight-brakelight bulb, use the follow-

ing procedure.

1. Turn the bulb socket assembly counterclockwise

and remove from the housing.

! WARNING

Do not attempt to remove a bulb when it is hot.
Severe burns may result.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 500H1




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды