Archon WD2010 Скачать руководство пользователя страница 13

INSTALLATION/OPERATION/MAINTENANCE INSTRUCTIONS FOR 

ARCHON MODELS WD2010L, WD2010, WD2010H WASHDOWN STATIONS 

 

 

 

 

Installation: 1004 Rev 4  

Issued: February 7, 2013

 

 

13 

 

CAUTION

 

Do not rotate connector (Item 103, Figure 5) after assembling the diaphragm.  
 

 

k.

 

Rotate the assembly in the vice so that the upper diaphragm casing (45) is upright. Place O-ring (39B) over 
end of extension (74) and connect extension to valve body using four-4 cap screws (100B). Cap screws 
should be torqued to 7-8 ft-lb. 

l.

 

Install tubing (171) to valve body connections hand-tight only.   

m.

 

Install steam check valve (75B) and spring (140A) in the valve body.  Install O-ring (39A) on the jet body 
(82). Ensuring that the two sides line up laterally, loosely assemble steam valve body (11) to the jet body 
(82) with two bolts and nuts (100), (4B).  Do not tighten bolts. 

m.

 

Attach tubing (171) to jet body and tighten connections.   

n.

 

Tighten two-2 bolts (100) at valve to jet connection. Bolts to be torqued to 30 ft-lb. 

o.

 

Assemble hose rack (246) and place in lower holes in the mounting lugs.  Secure in place with nuts (4A). 

 

 

5.

 

Re-Mounting 

a.

 

Re-mount the assembled unit with pipe spacers (79) and bolts (100A).  

b.

 

Tighten union coupling nuts (99) of manually operated steam and water valves (75S) (75W). 

c.

 

Reconnect discharge hose and spray gun assembly to unit.  

Refer to Section III Installation and Section IV Operation when returning washdown station to service. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание WD2010
















Отзывы: