ARB RD121 Скачать руководство пользователя страница 6

Страница: 6 / 40

2 Removing the Existing Differential

1.2

Tool-Kit Recommendations

Below is a list of tools and supplies you may need to complete this
installation. Requirements for your vehicle may vary. Please consult
your vehicle service manual for additional recommendations.

1.2.1

Tools

Standard automotive sizes (metric and/or imperial) of sockets,
wrenches, Allan keys, and drills.

A dial indicator or other suitable measuring tool for checking ring &
pinion backlash.

NOTE : Split ‘clamshell’ type Toyota differential housings

require a long series dial indicator to check backlash.

A razor knife for nylon tubing.

A torque wrench (See vehicle service manual for required torque
range)

A lubricant drain reservoir.

A slide hammer for removing CV axles.

Suitable measuring tools to measure a differential for preload
shimming. (e.g., an automotive feeler gauge)

A 11.2mm [7/16”] drill and ¼”NPT tap for bulkhead fitting
installation.

An automotive bearing puller (2 jawed) or a differential carrier
bearing puller.

A bearing press or arbor press.

1.2.2

Supplies

Thread lubricant/sealant compound (e.g., LOCTITE #567)

Thread locking compound (e.g., LOCTITE #272)

A gasket sealant or replacement gasket for your differential.

A sufficient volume of differential oil to completely refill your
housing. (see the

ARB

Air Locker Operating and Service Manual

for recommended lubricants)

A soap and water mixture to test for air leaks.

A selection of differential bearing shims to set-up preload and
backlash.

Содержание RD121








































Результаты поиска

Содержание RD121

Отзывы:

Похожие инструкции для RD121

Бренды по названию

Популярные бренды

ARB RD121, Инструкции по установке

Результаты поиска

Содержание RD121

Отзывы:

Похожие инструкции для RD121

Бренды по названию

Популярные бренды