72
Data Communication
SH-07E_E_09.fm
[72/75]
Use infrared communication to send and receive data to and
from other handsets which also support infrared
communication.
You can send and receive phonebooks, sp-mode mails, My
profile, business cards, memos, schedules, ToruCa, still pictures,
videos, etc.
The handset infrared communication function complies with
IrMC™ 1.1 standard. However, depending on the data, some
data may not be sent or received even when the other party’s
device complies with IrMC™ 1.1 standard.
Infrared communication is not available in Airplane mode.
To enter docomo apps password or passcode and to enter
authentication code are required for sending and receiving all
data items. The authentication code is a password exclusive to
infrared communication. Before starting data communication, the
sender and receiver must enter the same user-specified
four-digit code.
Face the infrared ports of the receiver’s and sender’s handsets
with each other and set the distance between them to
approximately 20 cm or less as shown.
While doing infrared communication, keep the infrared ports
facing each other and do not move them.
Infrared communication may not function properly in areas
exposed to direct sunlight, directly under fluorescent lights or
near equipment using infrared signals.
If either of the infrared ports is dirty, infrared communication will
become difficult. Take care not to scratch the ports, and wipe off
any dirt with a soft cloth.
When sending data, you can also operate from each function
(menu).
1
In the home screen, [
R
]
/
[Infrared]
2
Select an item
Send all
: Send all data by selecting an app.
Receive
: Receive single data.
Receive all
: Receive all data.
Open source licenses
: Display the open source licenses.
:
Perform the operations for receiving and sending at the same
time.
:
After the operation for receiving, the handset waits to receive
data. Infrared communication automatically begins when
data is sent from sender’s handset within approximately 60
seconds.
You can send and receive data with other handsets equipped
with iC communication function.
Make initial setting of Osaifu-Keitai in advance (
n
P. 45).
iC communication is not available during NFC/Osaifu-Keitai lock.
Data cannot be sent by iC communication in Airplane mode.
In the following cases, data may not be sent by iC
communication.
During charging
During earphone/microphone connection
During USB connection
You can send and receive phonebooks, My profile, bookmarks,
still pictures, videos, data recorded with the voice recorder, etc.
Use while placing the
a
mark of the receiver’s handset over
that of the sender’s handset as shown.
Do not move the handset until sending and receiving of data are
completed.
There may be some cases in which data are poorly sent and
received or the screen is off by positioning the handset near
depending on the other party’s handset. In this case, put a
distance between the
a
marks apart/closer or move them up/
down or to the left/right.
To enter authentication code is required for sending and
receiving all data items. The authentication code is a password
exclusive to iC communication. Before starting data
communication, the sender and receiver must enter the same
user-specified four-digit code. In addition, to enter passcode
may be required for sending all data items.
Data Communication
Infrared communication
Using infrared communication
When using infrared communication
Sending and receiving by infrared
Infrared port
Approx. 20 cm
or less
15°
15°
Note that if you select [Save] when receiving all data, all data
registered to the target function are deleted.
Receiving all data may not be available depending on the data
type.
When available space in the save destination becomes
insufficient while receiving data, the data being received to that
point are saved and receiving ends.
iC communication
Using iC communication
When using iC communication
Sending and receiving by iC
mark
SH-07E_E.book 72 ページ ２０１３年６月２５日 火曜日 午後２時２１分