Aquadart Rolla 8 Скачать руководство пользователя страница 11

Страница: 11 / 27

Note:

The product can be constructed either way up, for left or right hand opening.This instruction is showing a Left

hand opening.

IMPORTANT:if you are fitting the optional closing seal please refer to the steps on page 25.

H t

10mm

Step 1.1

Fit the Bottom Rail End Cap L/R (Part 10) on the fixed panel wall profile (Part 2) and closing wall profile(Part 29)

from the bottom. Place the wall profiles onto they tray,rough 10mm away from the front edge of the end cap.

Level the wall profiles using a spirit level then mark the profile through the pre-drill holes on the wall profiles.

(Diagram 1.1)

Step 1.2

Remove the wall profiles and drill the marked points using a 6mm masonry drill bit.(Diagram 1.2)

Step 1.3

Insert wall plugs(Part 8) then secure the fixed panel wall profile onto the wall using ST4X30 screws x4

(Part 9)(Diagram 1.3)

1.1

1.2

1.3

Note:

Ensure the channel with the pre-drill holes is facing outwards when placing the Wall Profile onto the tray.

Содержание Rolla 8




























Результаты поиска

Содержание Rolla 8

Отзывы:

Бренды по названию

Популярные бренды

Aquadart Rolla 8, Руководство по установке

Результаты поиска

Содержание Rolla 8

Отзывы:

Бренды по названию

Популярные бренды