background image

WARRANTY SERVICE

AquaCraft will warrant your Rio 51 for 90 days after 
purchase from defects in materials or workmanship of 
original manufacture. AquaCraft, at their option, will 
repair or replace at no charge the incorrectly made part. 
This warranty does not cover damage caused by crash, 
abuse, misuse, alteration or accident. To return your boat 
for repairs you need to provide proof of purchase. Your 
store receipt or product invoice will suffi ce.

IN NO EVENT SHALL THE PURCHASER BE ENTITLED TO ANY 
INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL 
DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE 
OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS 
IN THE PRODUCT. 

This warranty gives you specifi c legal rights and you may 
also have other rights, which vary from state to state.

FUJI-IMVAC ENGINES BT-28M 

3-YEAR LIMITED WARRANTY

USA AND CANADA

FJIG0128 BT-28M

Manufactured by FUJI-IMVAC INC.

Worldwide Distributor (except Japan): Hobbico, Inc.

Champaign, IL 61826 USA

http://www.fuji-imvac.com

Fuji-Imvac Engines warrants this engine to be free from 
defects in materials and workmanship for a period of three 
(3) years from the date of purchase. During that period, Fuji-
Imvac Engines will, at its option, repair or replace without 
charge any engine deemed defective due to those causes.

The warranty does not cover damage caused by customer 
disassembly, tampering, use of substandard fuel, use of 
incorrect accessories (spark plug, prop, etc.), or any use of 
the engine for which it is not specifi cally intended. Such 
uses will automatically void the warranty. If there is damage 
resulting from these causes within the stated warranty 
period, Fuji-Imvac Engines will, at its option, repair or 
replace it for a service charge not greater than 50% of the 
current manufacturer's suggested retail list price.

For service on your Fuji-Imvac Engines product, either in 
or out of warranty, please send it post paid and insured 
to Hobby Services. Along with your engine and proof 
of purchase date, please include a complete written 
explanation detailing the problem(s).  Please include your 
name, return address and daytime phone number so that 
you may be reached if needed.

Outside USA and Canada, contact local importer for 
warranty information.

Hobby Services 

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822
Attn: Service Department

Phone: (217) 398-0007

9:00 am - 5:00 pm Central Time M-F
E-mail: 

[email protected]

STANDARD REPAIR SERVICE

After the 90-day warranty has run out, you can still have 
your Rio 51 repaired for a service fee by the experts at 
AquaCraft. To speed up the repair process, please follow 
these four simple steps: 

IMPORTANT NOTE:

 For standard repair service you must 

specify whether you wish the charges to be billed COD or 
if you wish to be notifi ed of the charges so you can send 
a check.

1. It is best (recommended) to return the ENTIRE system, 
boat, radio and engine.

2. Make sure batteries are removed from the transmitter 
and receiver. Also make sure any gas and oil is drained 
from the tanks.

3. Send written instructions which include a list of all items 
returned and a THOROUGH explanation of the problem or 
problems needing service. Be sure to include your return 
address and daytime phone number. If you have access to 
e-mail please provide us with your e-mail address to help 
speed communication.

4. Send to the address as follows:

Hobby Services 

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822
Attn: Service Department

BOAT TERMINOLOGY

BOW:

 The front of the boat.

STERN:

 The back of the boat.

PORT:

 This is the left side of the boat when aboard and 

facing the front (bow). An easy way to remember this is 
that port and left both contain four letters.

STARBOARD:

 This is the right side of the boat when aboard 

and facing the front (bow).

HULL:

 The body of the boat.

DECK:

 The top of the boat.

TRANSOM:

 The back of the boat.

KEEL:

 The center of the bottom of the boat.

STRAKE:

 Lift rail(s) located on the bottom of the boat.

RUDDER:

 The hinged vertical plate mounted at the stern 

that controls steering.

STRUT:

 The propeller support bracket mounted on the 

transom of the boat.

3

Содержание Rio 51

























Отзывы: