background image

23

AquaCraft U-18 Miss Vegas

 Nitro RTR

Designer Jerry Dunlap is a 10-time national champion – no wonder the U-18 Miss Vegas RTR is a winner! The pre-
painted, 3-color fi berglass hull has fl otation, strengthening formers, and plenty of room to make every component 
easily accessible, including the installed .18 ABC marine engine, tuned pipe, header, and water-cooled head. The on-
board gear of the provided 2-channel radio system stays bone-dry inside the molded radio box. Its dual screw-attached 
lid has a tough rubber seal around the rim and a waterproof ON/OFF switch on the top! To fi ne-tune handling, adjust 
the factory-installed strut assembly – it can be angled slightly or moved up and down. The aluminum turn fi n and deep-
water rudder are strong and lightweight, and a water pick-up in the rudder channels cooling water to the engine head. 
AquaCraft includes a Y535 2-bladed prop and display/starting stand...just add fuel and radio batteries and you’re ready 
for action! 

AQUB32**

AquaCraft GrimRacer

Speed Grease Cable Lube 

This waterproof blue lubricant – with specially formulated, 
“non sling” properties – reduces friction and wear on fl ex 
cable and direct drive systems in gas, electric and nitro 
boats. 

AQUB9500

AquaCraft GrimRacer Cable Oil

Use GrimRacer Cable Oil with the Rio 51’s automatic fl ex 
cable lubricating system – a nearly effortless way to maintain 
the drive train a long life of peak performance. 

AQUB9550

Содержание Rio 51

























Отзывы: