3
Warranty Service
AquaCraft will warrant your Miss Seattle Hydroplane for 90 days
after the purchase from defects in materials or workmanship of
original manufacture. AquaCraft, at their option, will repair or
replace at no charge, the incorrectly made part. This warranty
does not cover damage caused by crash, abuse, misuse,
alteration or accident. To return your boat for repairs you need
to provide proof of purchase. Your store receipt or product
invoice will suffice.
IN NO EVENT SHALL THE PURCHASER
BE ENTITLED TO ANY INCIDENTAL, SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING
FROM THE USE, MISUSE OR INABILITY TO USE THE
PRODUCT OR FROM DEFECTS IN THE PRODUCT.
This
warranty gives you specific legal rights. You may also have
other rights, which vary from state to state.
Outside the USA and Canada, contact your local importer for
warranty information.
HOBBY SERVICES
Ph: (217) 398-0007
Attn: Service Department
9:00 am - 5:00 pm
3002 N. Apollo Drive, Suite 1
Central Time M-F
Champaign, Illinois 61822
E-mail: [email protected]
Safety Precautions
●
Never ever attempt to swim after a stalled R/C boat. Do
not get in the water for any reason to retrieve your boat.
To aid in retrieving a stalled R/C boat, set up a fishing
reel with a tennis ball tied to the end of the line. Better
yet, get yourself a small Jon boat so you can row out
and pick up your boat. Remember to use a PFD any
time you enter your retrieval craft.
●
AquaCraft products are to be used by ages 14 and over.
●
Do not touch the propeller anytime the motor is running.
Pay equally close attention to items such as loose clothing,
shirtsleeves, ties, scarves, long hair or anything that may
become entangled in the spinning prop. If your fingers,
hands, etc. come in contact with the spinning propeller, you
may be severely injured.
●
The speed and mass of this boat can inflict property damage
and severe personal injury if a collision occurs. Never run this
boat in the presence of swimmers or where the possibility
of collision with people or property exists.
●
Electric motors produce heat. Do not touch any part of your
motor until it has cooled.
●
This boat is controlled by radio signals, which are susceptible
to possible interference from other possible electrical noise.
●
In the event that weeds become entangled in the propeller,
stop the motor before attempting to remove them.
●
If your boat should happen to stall, water currents will slowly
carry it to shore. Keep in mind that the boat could be carried
to the opposite shore. When surveying areas to run your
boat, keep variables in mind such as wind direction, and
lake size. It is not advisable to run R/C boats on any free-
flowing bodies of water such as creeks or rivers.
●
Always remove the battery pack from the boat before
charging.
Specifi cations
MISS SEATTLE HYDROPLANE BOAT SPECIFICATIONS
Hull
length:
16.4" [416 mm]
Overall
length:
18" [458 mm]
Width:
8.8" [222 mm]
Height:
4" [102 mm]
Weight:
14.4oz [408 grams] (less battery)
Run
time:
4 to 6 minutes
BOAT FEATURES
➧
New Tactic TTX300 2.4GHz transmitter with lightweight
TR325 receiver.
➧
2200kv brushless in-runner motor with aluminum water
jacket.
➧
LiPo-ready (3S) 30 Amp brushless water-cooled motor
controller with low battery warning system and battery
cut off circuit.
➧
Tough, light-weight ABS construction with square
hatch opening for easy taping.
➧
Great-looking, pre-applied Miss Seattle graphics.
OTHER FEATURES
➧
Adjustable strut
➧
Music-wire drive shaft
➧
Pinch wire motor coupler
➧
Break-away wedge rudder
➧
One-piece aluminum turn fin
➧
1/8" [3.2mm] prop shaft
➧
Two blade 30mm FRP propeller
➧
Transom drain plug
MOTOR
KV
rating:
2200 kV
@
11.1V
Operating current: 1.4 A, 8V/ DC
(without
loading)
Input: 8 to 14V
Max current: 28 A /15 Seconds
Shaft diameter: 3.2 mm (1/8")
Motor resistance: 50 m
Dimensions:
27.5
×
30 mm (1.1"
×
1.2")
Weight: 71 grams (2.5 oz)
MOTOR CONTROLLER
Rated
Current:
30 amp
Battery
Connector:
Deans
®
Ultra Plug
®
Motor
Connector:
3.5 mm Bullet Plugs
Wire
Gauge:
14G
Warning
System:
9.6V Stutter Bump
LVC:
9V
BEC Max Current: 2A
PWM:
8K
Dimensions:
1.8"
×
0.9"
×
0.4"
(45 mm
×
24 mm
×
9 mm)
