Aquabot turboT Скачать руководство пользователя страница 7

Страница: 7 / 27

12ft / 4m

12ft. / 4m

Power Supply

Cleaner

Power Supply

Figure 6a

Place cleaner, upside down, in pool

to release air bubbles.

Let cleaner sink level to the bottom

of the pool (not on an incline)

Turn Power Supply “ON”

Figure 6b

Long

side of

pool

Mid-point

Power

Supply

NOTE: It is suggested to unplug your Power Supply when not in use to prevent accidental starts!

WARNING: The Power Supply must be placed at least 12 feet / 4 meters from the pool’s edge at all times!

WARNING: A Ground Fault Circuit Interrupter (GFCI) / Residual Current Device (R.C.D.) must be installed to protect your

electric outlet and to prevent any possible electrical shock!

3. CLEANER START POSITION

Plug the Power Supply Cord into a standard Ground Fault Circuit Interrupted (GFCI) / Residual Current Device (R.C.D.) protected

outlet. If your GFCI outlet is too far away and your cleaner does not have enough Cable to properly enter the pool at the midpoint

of its longest side then you may use a proper outdoor grounded extension cord, but always keep the Power Supply at least 12’ / 4

m from the pool’s edge! (Fig 6a-b)

2. SETTING UP THE POWER SUPPLY

TIP! To help protect your Cable from potentially getting pulled twisted, it is suggested to turn off your pool’s filtration system

while your cleaner is in operation to reduce the pool’s filter circulation effect that may push and circulate the Cable.

SETTING UP YOUR ROBOTIC POOL CLEANER

Содержание turboT




























Результаты поиска

Содержание turboT

Отзывы:

Похожие инструкции для turboT

Бренды по названию

Популярные бренды

Aquabot turboT, Руководство оператора и руководство по устранению неисправностей

Результаты поиска

Содержание turboT

Отзывы:

Похожие инструкции для turboT

Бренды по названию

Популярные бренды