Aquabot turboT Скачать руководство пользователя страница 22

Страница: 22 / 27

air

Careful removal of air trapped in the housing is critical to ensure natural balancing of your cleaner. Each time you place your cleaner

in the pool use the Floating Handle (while submersed) to turn your cleaner upside down turning it side to side to allow any possible

trapped air to escape!

FloaTiNg caBle (Page 7, seTTiNg uP The PoWer suPPly)

Ensure that the Floating Cable is untangled and spread out on top of the water, allowing enough length for your cleaner to reach all

areas of the pool without restriction and without excess of Floating Cable. Excess cable should be kept coiled

outside the pool near the Power Supply. For best results, place the Power Supply at the mid-point of the pool’s longest side (Page

7; Fig. 6a-b).

Should the Floating Cable continue to get tangled in or around the cleaner, contact an Authorized Service Center. To locate a

Service Center, please visit AquaProducts.com/SCL

cleaN FilTer Bag (Page 12, cleaNiNg aND chaNgiNg The FilTer Bag)

remove FloTaTioN (Page 13, FloTaTioN):

Remove Flotation one by one until proper buoyancy is returned. Be sure to always

submerge your cleaner and holding its Floating Handle turn upside down to remove any air that may be trapped within the cleaner’s

body. Careful removal of air trapped in the housing is critical to ensure natural balancing of your cleaner (Page 7, CLEANER START

POSITION).

FloaTiNg haNDle (Pages 5-6, FloaTiNg haNDle):

Check the handle position according to your model. Also check that

there is no water present inside the handle.

check The oPeraTioN oF The PumP moTor

Make sure Pump Motor (Page 3; Fig. 1) is working properly and that the Propeller is not being slowed or stopped due to debris

caught around it (Page 13, PROPELLER CARE).

If this situation persists, please visit your local Authorized Service Center. To locate a Service Center, please visit AquaProducts.

com/SCL

FilTer Bag

Ensure that the Filter Bag is properly mounted on the Wire Bag Support Frame (Page 12; Figs. 16a-b). The Filter Bag’s small Label

on the elastic edge should be on the outsdie of the bag and positioned at the center of either long side of the Bottom Lid Assembly

plastic. Stretch the elastic bottom over each Wire and slide the Filter Bag down until the Filter Bag reaches the Bottom Lid plastic.

At that point the Filter Bag’s elastic bottom should be stretched over the plastic lips located on each short side of the Bottom Lid

Assembly, and will hold the Filter Bag in place. Pull the Filter Bag top corners into each of the top 4 corners of the Wire Frame.

Insert the Bottom Lid into the bottom of the cleaner. Be sure that the Filter Bag’s fabric is not interfering with the locking of the Lock

Tabs. Be sure that each of the Lock Tabs are “Locked” closed (Page 12, CLEANING AND CHANGING THE FILTER BAG).

DeBris iNTake PorT FlaPs (Page 4; Fig. 3)

Check that the Intake Valve Flaps on the underside of your cleaner (in the Bottom Lid Assembly) move freely to open and close

(Page 4; Fig. 3). Clean Flaps if necessary.

lock TaBs (Page 12; Fig. 15)

Check that the Lock Tabs are not warped. They should be straight and aligned with the cleaner’s body. If they are warped then replacement

Lock Tabs are available for purchase through your Authorized Service Center. To locate a Service Center, please visit AquaProducts.com/

SCL

It is unlikely that both Motors (Drive Motor and Pump Motor) are experiencing mechanical problems. In most cases the issue lies

with something that is hindering the flow of electricity from the electrical outlet to the Power Supply (Page 4; Fig. 4) or through the

Floating Cable (Page 3; Fig. 2) to the cleaner itself. To locate and resolve where electrical flow is being hindered check the following:

elecTrical ouTleT & coNNecTioNs

Make sure that the Power Supply is firmly plugged into a grounded electrical outlet which has power. To test the outlet, plug in

another electrical instrument that you know works to the outlet.

FALLS OR FLIPS BACKWARDS OFF WALLS OR STAIRS

DEBRIS COMES OUT OF THE CLEANER WHEN REMOVING IT FROM POOL (BOTTOM LID DOES NOT

CLOSE PROPERLY)

DOES NOT PUMP WATER OR MOVE, OR POWER SUPPLY DOES NOT TURN ON

Содержание turboT




























Результаты поиска

Содержание turboT

Отзывы:

Похожие инструкции для turboT

Бренды по названию

Популярные бренды

Aquabot turboT, Руководство оператора и руководство по устранению неисправностей

Результаты поиска

Содержание turboT

Отзывы:

Похожие инструкции для turboT

Бренды по названию

Популярные бренды