background image

INSTALLATION GUIDELINES

 

COOLER PLACEMENT

 

Place your water cooler, in an area that is: 

● 

Not too humid, with a room temperature less than 26

C. 

● 

Close to a power point. Do not, however, plug it in yet. 

● 

Inside and out of significant direct sunlight and away from any heating appliance. 

● 

Well ventilated and dust/dirt free. Place cooler at least 5 cm away from any wall. 

● 

Secure bench that can safely support the weight of the cooler with a bottle of water fitted. 

● 

Water safe for when usage drips occur or in the unlikely event of leakage. 

Note: Never lift or carry your cooler by its taps or with bottle installed. Such action may void warranty. 

 

A WATER SAFE AREA

 

The purchaser (owner) acknowledges that water, like other liquids, can cause damage to surfaces and also 
create slip hazards. The purchaser takes full responsibility for placing the cooler in an appropriate position as 
per the guidelines above. The purchaser also acknowledges that any failure to address drips, leaks or spills is 
at their own risk. 

 

LIFTING AND CARRYING YOUR WATER COOLER

 

Don’t lift or carry the cooler by its taps as this may cause them to break. Don’t carry your cooler with a bottle 
fitted. Such action may cause harm and void your product warranty. 

 

DON’T LET YOUR COOLER RUN DRY

 

Never have the rear power switch on without water in the tank. 

 

FIXING YOUR WATER COOLER TO A WALL

 

To create greater stability for your water cooler you can fix the unit to a wall or similar solid structure. Wall 
fixing parts, bracket and screw, are supplied in the box with your water cooler. 

1.

 

On the rear of your water cooler remove the top left screw, located to the far left of the hot and cold 
power switches (Diagram 1) 

2.

 

Install the bracket back onto the rear of the cooler body in the same place where you removed the 
screw, using the removed screw. Ensure that the screw is tight. (Diagram 2) 

3.

 

Fix the other end of the bracket onto a wall or similar solid structure. (Diagram 3) 

Please Note: If you drill or screw into a wall it is critical to ensure that you do not interfere with any wiring, 
pipes or other matter inside of the wall. If you need assistance to do this please engage the services of a 
qualified tradesperson. 

 

 

Page 6 of 11 

Содержание ATGARGCOOL














Отзывы: