background image

WHAT TO EXPECT

CLEANER’S MOVEMENT

The robot uses a back/forth motion to clean your pool.  Because 
the axle is able to be positioned on an angle, this helps the cleaner 
move in a wider / tighter curve on it’s return path.  The illustrations  
highlight this pattern.  The amount of time it takes for the cleaner 
to make a pass in either direction is set and cannot be overridden.  
You may, however, adjust the duration of the overall cleaning cycle 
via the power supply.

CLEANER’S PERFORMANCE

Your cleaner is vacuuming at a rate that is over 75 gallons per 
minute.  This means that it’s picking up a lot of debris and it is 
recommended to keep the filter bags clean at all times.  For 
optimal performance the filter bags should be cleaned  after each 
cleaning cycle.

IMPORTANT: OPENING YOUR POOL

If you’re opening your pool for the first time this season, we 
recommend that you clean your pool manually to rid the pool of 
the heavy debris first and then use the robotic pool cleaner to 
maintain your clean pool.  

The reason: If your pool collects a massive amount of debris 
during the off-season,  putting the robot in first will cause the filter 
bags to fill much faster which means they will need to be cleaned 
more often.  

Sometimes when using the cleaner to vacuum an area that has 
heavy debris, it is normal to see a small portion of the debris leave 
the exit valve and go back into the pool or get pushed aside due 
to the small wave of water caused by the cleaner’s movement.  
After the cleaner’s cycle is complete, it is suggested to wait a few 
hours for the remaining debris in your pool to settle to the bottom 
and run the cleaner again to vacuum it up completely.

YOUR ROBOT’S TYPICAL CLEANING METHOD

Your robotic pool cleaner is designed to clean the dirt and debris from the pool bottom; and in some 
pools the cove and lower wall .  Below is the typical pattern your cleaner will attempt in your pool.  Pool 
dimensions and cleaning surfaces vary from pool to pool so coverage and cleaning patterns may vary.

• 

In pools that have 90 degree pool floor to wall transitions, this cleaner will clean the pool floor.

• 

In pools that have a radius of at least 6 inches from the pool floor to wall, this cleaner will also clean 
the pool cove and lower wall.

Содержание S2









Отзывы: