background image

1HP & 2HP Fusion Series Owner’s Manual

Page 2

Parts Included

Aerating Fountain (1)

Standard Nozzle Package (1)

Motor Cord with Quick Disconnect (1)

Mooring Rope (30m)

Mooring Stakes (2)

Optional Accessories

LED Lighting

Extended Nozzle Package

Twister Nozzle Package

Safety Instructions

IMPORTANT: Reading and understanding the instructions and warranty disclaimer are

necessary prior to product installation and operation.

Under NO circumstances should anyone enter the water with the electrical equipment plugged in.

NEVER run the unit out of the water. It may damage the motor seals.

NEVER lift or drag the fountain by the power or light cord.

Suitable for FRESHWATER applications only.

The fountain suction screen should be inspected for clogging on a monthly basis. If matted weeds, leaves,

or plastic bags are present, remove them with a bristle brush. Failure to keep the suction screen clear of

blockages will cause low water flow and may cause premature motor failure. This type of failure is NOT

covered under the Manufacturer’s Warranty.

In freezing conditions, the fountain must be removed from the water body and stored in an area above 0°C.

The  manufacturer,  importers  or  its  distributors  are  not  liable  for  electrician’s  fees  incurred  for

troubleshooting electrical issues.

~ Table of Contents ~

Steps to Prep Fusion for Water................... 3

Nozzle Build

Individual Nozzle Instructions in Appendix A

Mooring & Light Installation

Fusion Pump Parts List............................ 5

Fusion Vertical Parts List......................... 6

Troubleshooting Guide ........................... 7

Appendix A ................................................ 8

Standard Nozzle Package

1.

Cluster Arch ........................................A1

2.

Daffodil ..........................................A2

3.

Flare................................................A3

4.

Lily..................................................A4

5.

Super Lily.............................................A5

6.

Tornado..........................................A6

Содержание AQUATIC 1HP FUSION Series















Отзывы: