APRILIA SCARABEO 50 I.E-100 4T - 2001 Скачать руководство пользователя

Страница: 18 / 110

Release 00

2003-02

Scarabeo 50 I.E.-50/100 4T

IDENTIFICATION DATA

Please supply the frame number when you purchase
spare parts.

NOTE

Do not obliterate or alter the identification

numbers under any circumstance. This is illegal in all
countries. In addition, alteration of the identification
numbers invalidates the warranty.

FRAME NUMBER

The frame number (1) is stamped on the central tube of
the frame. To be able to read it, it is necessary to remove
the cover (2).

ENGINE NUMBER

The engine number (3) is stamped near the lower
support of the rear shock absorber.

100

Содержание SCARABEO 50 I.E-100 4T - 2001















































































































Результаты поиска

Содержание SCARABEO 50 I.E-100 4T - 2001

Отзывы:

Похожие инструкции для SCARABEO 50 I.E-100 4T - 2001

Бренды по названию

Популярные бренды

APRILIA SCARABEO 50 I.E-100 4T - 2001, Руководство по ремонту

Результаты поиска

Содержание SCARABEO 50 I.E-100 4T - 2001

Отзывы:

Похожие инструкции для SCARABEO 50 I.E-100 4T - 2001

Бренды по названию

Популярные бренды