APRILIA SCARABEO 100 - Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 96

APRILIA SCARABEO 100 - Скачать руководство пользователя страница 73

73

use and maintenance

Scarabeo 50 - Scarabeo 100

2%#(!2').' 4(% "!44%29

Carefully read p. 70 (BATTERY).

◆

Remove the battery (complete removal),
see p. 72 (REMOVING THE BATTERY).

◆

Prepare an appropriate battery charger.

/

NOTE

Do not remove the battery plugs;

without plugs the battery may be damaged.

.

◆

Unscrew and remove the element plugs.

◆

Check the electrolyte level, see p. 72
(CHECKING THE ELECTROLYTE LEV-
EL

◆

Connect the battery with a battery charg-
er.

NOTE

A recharge with an amperage

equal to

1/10th

of the battery capacity is

recommended.

◆

Switch on the battery charger.

.

◆

After the recharging operation, check the
electrolyte level again and if necessary
top up with distilled water.

◆

Replace the element plugs.

a

CAUTION

Reassemble the battery only 5-10 min-
utes after disconnecting the recharger,
since the battery continues to produce
gas for a short lapse of time.

).34!,,).'

4(% "!44%29

Carefully read p. 70 (BATTERY).

◆

Make sure that the ignition switch is in
position “

m

”.

◆

Put the battery in its container.

.

◆

Connect the breather pipe.

a

CAUTION

Always  connect  the  battery  breather
pipe, to prevent the sulphuric acid va-
pours from corroding the electric sys-
tem, painted parts,  rubber elements or
gaskets  when  they  exit  the  breather
pipe itself.
The breather pipe must be connected in
such a way as to prevent any crushing,
otherwise the pressure inside the bat-
tery may increase with consequent risk
of damage.

◆

Connect, in order, the positive (red) (

+

)

and negative (

–

) cable.

◆

Cover the terminals with special grease
or Vaseline.

a

CAUTION

Upon reassembly the electric cables
must be guided in the correct position,
in such a way as not to crush them.

The negative cable (

–

) must not overlap

the positive cable (+) fastening, but it
must be positioned beside it, between
the battery and the compartment.

◆

Push the battery inside the battery com-
partment.

◆

Close the battery cover (1).

◆

Screw and tighten the screw (2).

◆

Put back the inspection cover, see p. 62
(REMOVING THE INSPECTION COV-
ER).

«
...
71
72
73
74
75
...
»

Содержание SCARABEO 100 -

































































































Отзывы:

Нет отзывов