APRILIA SCARABEO 100 - Скачать руководство пользователя страница 54

Страница: 54 / 96

use and maintenance

Scarabeo 50 - Scarabeo 100

&2/.4 7(%%,

DISASSEMBLY

CAUTION

The disassembly and reassembly of the
front wheel may be difficult for unskilled
operators.

If necessary, contact an

APRILIA

Official

Dealer.
If you want to perform these operations
personally, keep to the following in-
structions.

Carefully read p. 45 (MAINTENANCE).

While disassembling and reassembling
the wheel, be careful not to damage the
brake pipes, the discs and the pads.

◆

Position the vehicle on the centre stand
on firm and level ground.

NOTE

Prepare a support with base

measuring 200 x 200 mm, whose height
should be 270 mm for the

and 230 mm

for the

◆

Place the support under the vehicle and
a spongy cloth between them, so that the
front wheel can move freely and the ve-
hicle cannot fall down.

CAUTION

Make sure that the vehicle is stable.

◆

Put a support (1) under the tyre, in such
a way as to keep the wheel in its position
after loosening it.

◆

Loosen the screw (2) of the wheel pin
clamp.

◆

Unscrew the wheel pin (3) completely.

Wheel pin driving torque:
50 Nm (5 kgm).

◆

Support the front wheel and manually
withdraw the wheel pin (3).

◆

Take the washer (4).

CAUTION

Never pull the front brake lever after re-
moving the wheel, otherwise the caliper
pistons may go out of their seats, thus
causing the outflow of the brake fluid.
In this case consult your

APRILIA

Official

Dealer, who will carry out the proper
maintenance operation.

◆

Make the front wheel adv ance until you
can withdraw the disc from the brake cal-
iper (5).

◆

Without removing the brake caliper,

rotate the left rod (6) clockwise, in such a
way as to create the space necessary to
withdraw the wheel.

◆

Withdraw the front wheel completely.

◆

Disconnect the odometer control (7).

Содержание SCARABEO 100 -

































































































Результаты поиска

Содержание SCARABEO 100 -

Отзывы:

APRILIA SCARABEO 100 -, Руководство пользователя, Страница: 54 / 96

Результаты поиска

Содержание SCARABEO 100 -

Отзывы: