APRILIA RS 660 Скачать руководство пользователя

Страница: 260 / 420

•

Remove the washer (3).

•

After having adequately protected the

instrument cluster, remove the plate

(4) complete with semi-handlebars and

rest it on the instrument cluster sup-

port.

•

Remove the safety plate, unscrew the

counter-lock ring, remove the rubber

shim and then unscrew the lower ring

nut using the special tool in order to re-

peat the steering assembly tightening

procedure in the correct way.

•

Pre-tighten the ring nut (5) to 60 Nm

(44.25 lbf ft).

•

Turn the handlebar to the left and right

as far as it will go to seat the bearings.

•

Unscrew the ring nut and tighten it

again to 40 +/- 5 Nm (29.50 +/- 3.68 lbf

ft).

•

Reassemble the previously removed components and check the handlebar resistance to

rotation that must be 250 +/- 100 g (0.55 +/- 0.22 lb) in both directions.

Suspensions

RS 660 - Tuono 660

SUSP - 260

Содержание RS 660





































































































































































































































































































































































































































Результаты поиска

Содержание RS 660

Отзывы:

Похожие инструкции для RS 660

Бренды по названию

Популярные бренды

APRILIA RS 660, Руководство по обслуживанию станции

Результаты поиска

Содержание RS 660

Отзывы:

Похожие инструкции для RS 660

Бренды по названию

Популярные бренды