APR APR-2000-SCS Скачать руководство пользователя страница 20

Страница: 20 / 79

3651 WALNUT AVENUE, CHINO CA 91710 • PHONE (909) 664-9980 •

APR-Rework.com

Page

TB-10006 REV December 2018

Employee Owned

Profile Data Table

• 1 System Performance information

• Displays 8 user-defined profile markers (performance)

• Provides temperature and ramp rate data

Changing Profile Marker location - Method 1

• Left click the desired profile marker. The cursor will change

to double arrows. Drag & drop to the desired time.

Changing Profile Marker location - Method 2

• Right click the profile marker. The time adjust dialog box will

appear. Use the up and down arrows to select the desired

time. Click"ok" to enter the desired time.

Repeatability verification:

•If external thermocouple plots were saved as part of a previous run.

•Left click “Real Time” data box on the appropriate external TC1,2,3 to

enable / disable a comparison plot for the next run.

Содержание APR-2000-SCS
















































































Результаты поиска

Содержание APR-2000-SCS

Отзывы:

Похожие инструкции для APR-2000-SCS

Бренды по названию

Популярные бренды

APR APR-2000-SCS, Руководство пользователя

Результаты поиска

Содержание APR-2000-SCS

Отзывы:

Похожие инструкции для APR-2000-SCS

Бренды по названию

Популярные бренды